810784
13
Zoom out
Zoom in
Previous page
1/24
Next page
13
ENGLISH
INSTALLATION
INSTALLER
THE FLUE:
Further to the general prescriptions for the fumes duct
and flue, the flue:
must only be used for discharging fumes
must be correctly sized to satisfy the requirements
for fume discharging (EN 13384-1)
should preferably be insulated, in steel with a
circular internal section. If rectangular, the corners
must have a radius of not less than 20 mm, with a
ratio of the internal dimensions of <1,5
must normally be at least 1,5 metres in vertical
length
must have a constant cross section
must be waterproof and thermally insulated to
ensure a good draw
must preferably have a collection chamber for
non-combusted matter and condensation.
if pre-existing, must be clean, to prevent the fire
hazard.
in general, we recommend fitting a tube inside the
existing masonry chimney if its diameter is greater
than 150 mm.
INTUBATED SYSTEM:
Further to the general prescriptions for the fumes duct
and flue, the intubated system:
must operate in negative pressure;
must be open to inspection
must observe local regulations.
THE CHIMNEY POT
must be anti-downdraught
must have an internal cross section equivalent to
that of the flue and a fumes outlet at least double
that of the interior of the flue
for dual flues (which should be spaced at least 2
m apart) the chimney pot receiving the fumes from
the solid fuel appliance or that from the higher
storey, must be at least 50 cm higher than the other
it must extend beyond the back flow zone (in Italy,
refer to UNI 10683 point 6.5.8.)
it must allow for maintenance of the chimney.
EXTERNAL AIR INTAKE
In general, we suggest two ways to ensure a proper
flow of combustion air.
Indirect air intake
Install an air outlet at floor level with an effective surface
area (net of the screen or other protections) of at least
80 cm2 (10 cm in diameter).
To prevent draughts, we recommend installing the
intake behind the stove or behind a radiator.
Installing it in front of the appliance will create
unpleasant draughts.
Direct air intake**
Install an air intake with an effective size (net of the
mesh or other protective equipment) that is at least
equal to that of the air intake at the back of the product.
Connect the air intake to the appliance’s air intake with
a pipe that may also be flexible.
Increase the diameter of the pipe if the pipe is not
smooth: assess any load loss.
We recommend that it does not exceed 1 metre in
length or include any bends.
The air maybe drawn from an adjacent room only if:
the flow is taken from permanent and unobstructed
openings communicating with the outdoors;
the air pressure in the adjacent room is never
lower than that of the outdoor pressure;
the adjacent room is not a garage, subject to fire
hazard, a bathroom or a bedroom;
the adjacent room is not a shared room in the
condominium.
In Italy, UNI 10683 provides that ventilation is sufficient
even if a pressure difference between the outdoors
and indoors of no more than 4 PA is guaranteed (UNI
EN 13384-1). The installer who issues the declaration
of conformity is responsible for ensuring these
conditions.
** Direct connection to the air intake will not make the
product airtight.
It is therefore necessary to additionally ensure an
air intake from within the room where the product is
installed (i.e. for cleaning the glass)
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edilkamin Klik at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Klik in the language / languages: English as an attachment in your email.

The manual is 1.47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Edilkamin Klik

Edilkamin Klik Usermanual and installation guide - German - 24 pages

Edilkamin Klik Usermanual and installation guide - Dutch - 24 pages

Edilkamin Klik Usermanual and installation guide - French, Italian - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info