810738
29
Zoom out
Zoom in
Previous page
1/142
Next page
ENGLISH
- 29 -
INSTRUCTIONS FOR USE
ELECTRICAL CONNECTIONS
GENERAL WARNINGS
The electrical safety of the system is ensured only when
it is properly connected to an effective grounding system,
implemented according to applicable safety standards: the
gas,waterandheatingpipingaredenitelynotsuitableas
grounding points.
You must check this fundamental safety requirement; if in
doubt, request an accurate electrical check by a professionally
qualiedtechnician,asthemanufactureroftheboilerstoveis
not responsible for any damage caused by failure to ground the
system.
Getqualiedpersonneltocheckthattheelectricalsystemis
adequateforthemaximumpowerabsorbedbythesystem,in
particular ensuring that the section of the cables is suitable for
the power absorbed by the loads.
The use of any components that use electricity entails the
observance of some fundamental rules:
•donottouchtheappliancewithpartsofthebodywhichare
wet and/or damp, and/or with bare feet;
•donotpullelectricalcables;
•donotallowtheappliancetobeexposedtotheelements
(rain,sun,etc.)unlessthisisexpresslyprovidedfor;
•donotallowtheappliancetobeusedbychildrenornon-
experts.
230V electrical power supply connection
Installation of electrical accessory components to the boiler
stove requires electrical connection to a 230 V - 50 Hz
network.
This connection must be professionally carried out as laid
down in local regulations in force at the installation location.
Caution:
The electrical installation must be carried out only by a
qualied technician.
Before carrying out any connections or any operation on
the electrical parts, always disconnect the power supply.
We remind you that it is necessary to install a two-pole
switch on the boiler stove power supply line, with contact
gap greater than 3 mm, which is easily accessible, so as to
make any maintenance operations fast and safe.
Replacement of the power cable must be carried out by
authorised technical personnel.
Failure to comply with the above may compromise the safety
of the device.
HYDRAULIC KIT/MOTHERBOARD ELECTRICAL
CONNECTION
The hydraulic kit comes with cabling connected to a connector
(A).
The connector from the hydraulic kit, once mounted, must be
connected to the connector coming from the motherboard (B)
mounted on the product.
The attachments can only be inserted in one direction, therefore
you do NOT need to use unnecessary force.
AB
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edilkamin Kit - R-RW-R2-RW2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Kit - R-RW-R2-RW2 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 18.38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info