810738
27
Zoom out
Zoom in
Previous page
1/142
Next page
ENGLISH
- 27 -
INSTRUCTIONS FOR USE
HYDRAULIC CONNECTION
FLUSHING THE SYSTEM
Fit suitable gate shut-off valves to the heating system piping.
To protect the heat system from corrosive damage,
encrustations or deposits, it is important, before installation of
theappliance,toushthesystem.Thismustbecarriedoutin
accordance with UNI-CTI 8065, using suitable products such
as,forexample,SentinelX300(newsystems),X400andX800
(oldsystems)orFernoxCleanerF3.
Complete instructions are provided with the products but,
for further information, you can contact the manufacturers
SENTINELPERFORMANCESOLUTIONSLTDor
FERNOXCOOKSONELECTRONICSdirect.
Afterushingthesystem,toprotectitagainstcorrosionand
deposits,werecommendusinginhibitorssuchasSentinel
X100orFernoxProtectorF1.
It is important to check the concentration of the inhibitor after
eachsystemmodicationandduringeachmaintenancecheck,
following the manufacturers instructions (suitable tests are
available at retailers).
The safety valve bleed must be connected to a collection funnel
to channel any purging during intervention.
Information:
Failure to ush the heating system or to add an adequate
inhibitor invalidates the warranty of the equipment and of
other accessories such as pumps and valves, for example.
FILLING THE SYSTEM
Filling must be done slowly so as to allow air bubbles to
come out through the appropriate vents, located on the heating
system.
For closed circuit heating systems, the load pressure of the
systeminacoldstateandthepre-inationpressureofthe
expansiontankmustbethesame.
•Inopenvesselheatingsystems,directcontactbetweenthe
circulating liquid and the air is enabled.
During the heating season, the end user must regularly check
thelevelofcirculatingwaterintheexpansiontank.
The recirculation system water content must be constantly
maintained.
Regular monitoring of the water level should be carried out
every 14 days to maintain an almost constant water content.
Ifadditionalwaterisrequireditmustthellingprocess
must be carried out, when the boiler stove is cooled to room
temperature.
These precautions are designed to prevent the onset of thermal
stress in the steel body of the boiler.
•Insystemsequippedwithanexpansiontank,thewater
pressure in the stove boiler - when the system is cold - must not
be lower than 0.3 bar;
•Thewaterusedforllingtheheatingsystemmustbe
decontaminated and contain no air.
Caution!
Do not mix the heating water with anti-freeze or anti-
corrosion agents in the wrong concentrations!
This can damage the seals and cause noises to occur during
operation.
The manufacturer is not liable in the event of damage to
people or property caused by failure to comply with the
above.
Once all the hydraulic connections are in place, proceed to
verication of the pressure seals, by lling the boiler.
This operation must be carried out with caution, adhering to the
following steps:
•opentheairreleasevalvesontheradiators,boiler,andinthe
system;
•graduallyopenthesystemwatertap,makingsurethatany
automatic air vent valves installed in the system are working
properly;
•closetheventvalvesontheradiatorsassoonaswaterleaks
out;
•checkonthebuilt-insystemmanometerthatthepressure
reaches about 1 bar (only applies to closed vessel systems -
check local regulations or standards to ensure that they allow
it); for open vessel systems, water make-up is automatic via
the vessel itself;
•closethesystemwatertapandthenagainreleasetheair
through the air release valves on the radiators;
•checkthetightnessofallconnections;
•afterhavingcarriedouttherstboilerignition,andbrought
the system up to temperature, stop the pump operation and
repeat the air venting operations;
•allowthesystemtocooland,ifnecessary,restorewater
pressure to 1 bar (only applies to closed vessel systems -
check local regulations or standards to ensure that they allow
it); for open vessel systems, water make-up is automatic via
the vessel itself
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edilkamin Kit - R-RW-R2-RW2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Kit - R-RW-R2-RW2 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 18.38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info