499659

Edilkamin IDROTECH Manual

36
Zoom out
Zoom in
Previous page
1/115
Next page
- 36 -
the ame does NOT appear Flames appear
Flames appear, but after the word “Start”, the
message “Start Faile appear
Check:
- combustion chamber position and cleanliness.
- if the heating element is working.
- room temperature (if lower than 3°C use a relighter) and
damp.
Try to light with a relighter.
Check: (for the DEALER)
- if the thermocouple is working.
- start-up temperature setting in the parameters.
5) Power failure
Check the electrical connection and for voltage drops.
6) Termoc broken (this trips if the thermocouple fails or is disconnected).
Check connection between the thermocouple and the circuit board. Check operation with cold tests.
7) Over temp (shutdown due to excessive smoke temperature).
Excessive smoke temperature may be caused by: the type of pellet, smoke extraction fault, blocked duct, incorrect installation,
or gearmotor “drift”.
8) H2O Alarm (this trips if the water temperature detector reads a temperature of above 90°C).
Excessive temperature may be caused by:
undersized system: have the DEALER enable the ECO function.
clogging: clean heat exchange pipes, the combustion chamber and smoke outlet.
9) No Depression (this trips if the ow sensor detects insufcient combustion air ow).
The ow may be insufcient because the door is open, the door does not close properly (e.g. bad seal), there is an air intake or
smoke extraction problem, the combustion chamber is clogged, or the ow sensor is dirty (clean with dry air).
Check the ow sensor threshold among the parameters (for the DEALER).
The low pressure alarm may also occur during ignition.
Pellets may NOT fall into the combustion chamber for the following reasons:
• There are no pellets: ll the hopper.
• The screw feeder is empty: ll the screw feeder by pressing the + and - keys together.
• Some pellets have jammed in the hopper: empty the pellet hopper with a vacuum cleaner.
• The gearmotor has broken down.
• The screw feeder safety thermostat has “disconnected” the electricity power supply from the gearmotor: make sure there is
no overheating. Check using a volt-ohm-milliammeter or t a temporary jumper.
• The excess water temperature safety thermostat has “disconnected” the electricity power supply from the gearmotor:
check if there is water in the stove. Press the button behind the stove to reset.
It is essential to contact a DEALER before starting up again.
FAQ
The answers shown here summarize the information found in these specications.
1) What ttings do I need in order to install Idrotech?
Smoke outlet of at least 80 mm in diameter.
Air intake in the room of at least 80 cm2.
¾” G manifold outlet and inlet.
¾” G outlet to drain for overpressure valve.
Coupling for ¾” G lling line.
Connection to an electrical system compliant with standards, with a 230 V +/- 10% 50 Hz thermal-magnetic circuit breaker.
Refer to page 22 for dimensions. Read the installation safety information on page 25.
2) Can I use the stove without water?
NO. Use without water damages the stove.
3) Does the Idrotech stove give out hot air?
NO. All the heat goes where it is needed: to the water. Part of the heat produced is radiated into the room. You are advised to t
heat emitting units (radiators) in the room.
4) Can I connect the stove inlet and outlet directly to a heat emitting unit (radiator)?
NO, like all other water heaters, they must be connected to a manifold from which the water is distributed to the heat emitting
units.
There are two distinct cases:
ENGLISH
ENGLISH
… 36 …


Need help? Post your question in this forum.

Forumrules
1

Forum

edilkamin-idrotech

Reset search

  • quando la stufa non é funzionante nel display esce la scritta "bat 1" e lampeggia. qual'é il motivo? Submitted on 30-3-2022 at 15:44

    Reply Report abuse

    • Prova a cambiare la batteria del CMOS e tipo quella del telecomando della machina se non sbaglio 3510 Answered on 24-9-2022 at 01:04

      Vote up Report abuse

  • avendo un impianto piccolo vorrei attivare la funzione eco nella mia stufa idrotech come si fa? Submitted on 7-11-2021 at 19:54

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edilkamin IDROTECH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin IDROTECH in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info