499659

Edilkamin IDROTECH Manual

30
Zoom out
Zoom in
Previous page
1/115
Next page
- 30 -
THE INTERFACE
Panel with display and 4 keys
0/1 : to turn on and off.
Menu: to access the menu
+ and -to increase/decrease the various settings.
USE
Before ignition. 1st Ignition: contact your local DEALER.
The rst few times the stove is ignited there may be a slight smell of paint, which disappears rapidly.
Before ignition, check:
• that the stove has been installed and water connected correctly (make sure the system has been bled).
• The power supply.
• THE SWITCH ON THE ELECTRIC SOCKET BEHIND THE STOVE IS TURNED TO 1.
• the door is closed.
• the combustion chamber is clean.
• the display is on standby.
SCREW FEEDER LOADING.
If the pellet hopper empties, press the + and - keys together to ll the screw feeder.
This must be done before igniting the stove again if it has shut down due to running out of pellets.
It is normal for a few pellets to be left in the hopper, which the screw feeder is not able to pick up.
IGNITION
Automatic ignition
Hold the 0/1 key down for two seconds with the stove on standby to start the ignition procedure. The word Start appears on the
display for a few minutes (ignition does not take a preset time:
it is automatically shortened if the electronics detect that certain tests are passed). The ame appears after about ve minutes.
It is normal for a little smoke to be seen in the combustion chamber before the ame appears. Start remains on the display until the
ame is stable.
Manual ignition
At temperatures of less than 3°C (too low for the heating element to glow) or if the heating element is temporarily out of order, a
relighter may be used for ignition. Put a piece of well lit relighter into the combustion chamber, close the door and press the 0/1
button.
OPERATING MODES
Set the water temperature required in the system (60°C recommended) on the panel. The stove modulates the power to maintain or
reach this temperature.
The Eco function may be enabled for small systems (see DEALER adjustments). In this case, the stove turns off when the water
reaches the set temperature and turns back on again to modulate the power.
Pressure gauge
It is mainly useful to technicians.
It is located on the rear left of the stove and shows the
water pressure in the system. The pressure must always be
between 1 and 1.5 bars when the stove is running.
ENGLISH
ENGLISH
… 30 …


Need help? Post your question in this forum.

Forumrules
1

Forum

edilkamin-idrotech

Reset search

  • quando la stufa non é funzionante nel display esce la scritta "bat 1" e lampeggia. qual'é il motivo? Submitted on 30-3-2022 at 15:44

    Reply Report abuse

    • Prova a cambiare la batteria del CMOS e tipo quella del telecomando della machina se non sbaglio 3510 Answered on 24-9-2022 at 01:04

      Vote up Report abuse

  • avendo un impianto piccolo vorrei attivare la funzione eco nella mia stufa idrotech come si fa? Submitted on 7-11-2021 at 19:54

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Edilkamin IDROTECH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin IDROTECH in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info