Manual Edilkamin Firebox Luce Plus (page 24 of 80) (English, German, French, Italian, Portuguese, Spanish)

810851

Zoom out

Zoom in

1/80

- 24 -

ENGLISH

WARNINGS

Installing Firebox®

Besides the contents of this document,

please take into consideration the UNI stand-

ards:

- no. 10683 - Wood-Burning Heating Appli-

ances: Installation Requirements.

- no. 9615/90 - calculation of the inner di-

mensions of ﬁ replaces.

Speciﬁ cally:

- before starting any installation operation,

it is important to check the compatibility of

the system as established by the UNI 10683

standard.

- after installation, the installer must "start-

up" the system and issue the documentation

required by the UNI 10683 standard.

Using Firebox®

Smoke damper adjustment: in the event of

difﬁ culty clearing the smoke (low draught),

evacuation can be improved by adjusting the

screw on the damper control rod.

By turning the screw (clockwise) and closing

the door, the damper will remain slightly in-

clined, helping the smoke to ﬂ ow out.

Ash tray: during operation, it must always be

completely closed; otherwise a "forge effect"

is created with consequent damage to the

Firebox® structure and covering components.

Efficiency and fuel consumption: to obtain

the declared efﬁ ciency, it is necessary to burn

3.5 - 4 kg/h of wood (depending on the model

as shown in the technical speciﬁ cation table);

use with an excessive amount of wood may

cause damage.

When Firebox® is running at full power, it gen-

erates a signiﬁ cant amount of heat. There-

fore, during installation, carefully check that

there are no areas of contact with wood or

other combustible materials and that any

such materials are out of range of the heat

which radiates from the ﬁ replace.

There should be insulation between Firebox®

and these materials or a gap of at least 3 cm

with free air ﬂ ow, to prevent excessive heat

build-up.

Special front protection panels are available

for beams on request.

Electrical connections

(for forced ventilation versions)

- These must conform to professional installa-

tion and construction standards.

- The electrical components are always live;

before any maintenance, disconnect the plug

and turn off the electrical panel of the dwell-

ing.

- Avoid contact between electrical wires, Fire-

box® and the ﬂ ue.

- The electrical equipment supplied with Fire-

box® must not be tampered with in any way.

For further details, con-

sult the following document:

“Firebox® Instructions for use" attached to the

product.

EXTERNAL AIR INTAKE (Figs. A-B)

The connection with the outside, made with

a cross-sectional area of at least 80/200 cm²

(depending on the model) is absolutely es-

sential, as prescribed by the standard gov-

erning installation requirements (UNI 10683).

It must, therefore, be provided.

It is made with a duct that must bring outside

air directly to the adjustment mechanism

(Fig. B). The regulation mechanism must be

attached to the bottom of Firebox®.

During installation, carefully seal the points

where the external air may leak.

The external air duct may come from behind,

from below, from the side, or consist of a ﬂ ex-

ible hose which runs directly from the outside

to the mechanism vent (Fig. B).

It is advisable to apply a protection grille on

the outside of the air-intake duct that does

not, reduce the air-ﬂ ow capacity.

The external air must be drawn in at ﬂ oor

level.

If it is not possible to do as described above,

place the external air intake as near to Fire-

box® as possible.

SUPPORT STAND

UNIVERSAL OPTION (Fig. L)

Screw the 2 frame-fastening brackets (A) to

the bottom of the Firebox® structure, using

the ø 3.6 holes and the six 4.8x13 screws

provided.

At the pre-cuts, cut the vertical tubes of the

support frame (B) to the desired height for

positioning Firebox®.

Using the pins provided, ﬁ t the frame (B) to

the brackets (A) previously fastened to Fire-

box®.

Take care that the horizontal projections (C)

of the frame are on the rear facing the wall.

Lock the support stand with the four 8x40

screws provided.

Position Firebox® with stand and fasten to

the ﬂ oor using the anchors and 8x70 screws

provided.

FLUES (Fig. N)

The Firebox® smoke outlet has a circular

cross-section. It is provided to allow the use

with EdilKamin stainless steel pipes (rigid sin-

gle-wall or insulated rigid double-wall), that

allow a quick, secure connection to the ﬂ ue.

If the ﬂ ue inlet is not

vertical in relation to the

ﬁ replace, the connection between the ﬁ re-

place and ﬂ ue must not narrow or slope by

more than 45° (1-3).

In the case of old or oversized ﬂ ues, it is

advisable to line them with stainless steel

pipes of a suitable diameter and with suit-

able insulation. For ﬂ ues located outside, we

recommend using the stainless In the case of

outdoor ﬂ ues, it is advisable to use insulated

double-wall stainless steel pipes.

The constructional features, in particular as

regards mechanical strength, insulation and

gas-tightness, must be able to withstand a

smoke temperature of at least 450 °C.

Use high temperature mastic to seal where

the steel pipe connects to the Firebox®

smoke outlet.

Using the rigid, stainless steel ﬂ ue requires a

female-female ﬁ tting on the smoke outlet of

the ﬁ replace.

The chimney pot should be placed in full wind.

FIREBOX® Installation Instructions

Fig. N

Fig. A

Fig. B

BB BB

Fig. L

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Firebox Luce Plus in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 2.51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Edilkamin Firebox Luce Plus

Edilkamin Firebox Luce Plus User Manual - English - 24 pages

Edilkamin Firebox Luce Plus User Manual - German - 28 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Edilkamin Firebox Luce Plus Manual

Product: