Manual Edilkamin Firebox Deco (page 13 of 24) (English)

810849

Zoom out

Zoom in

1/24

ENGLISH

INSTALLATION

INSTALLATION IN AN EXISTING FIREPLACEINSTALLATION IN AN EXISTING FIREPLACE

FITTED WITH EXTERNAL AIR INTAKEFITTED WITH EXTERNAL AIR INTAKE

(when part numbers are not specifi ed, refer to the (when part numbers are not specifi ed, refer to the

specifi cation tables on the previous pages)specifi cation tables on the previous pages)

N.B.: if you do not want to alter the existing hood, the N.B.: if you do not want to alter the existing hood, the

installation must be carried out without hot-air ducting installation must be carried out without hot-air ducting

(leaving the upper outlets closed).(leaving the upper outlets closed).

In this case, the hot air only enters the room through In this case, the hot air only enters the room through

the slots on the front, above the door.the slots on the front, above the door.

a) make a pit (Fig. A), in the basement of the existing a) make a pit (Fig. A), in the basement of the existing

fi replace, big enough to hold the external air intake fi replace, big enough to hold the external air intake

mechanism (Fig. B)mechanism (Fig. B)

b) this pit must communicate with an external air inlet b) this pit must communicate with an external air inlet

duct through a passage with cross-sectional area of at duct through a passage with cross-sectional area of at

least 80-200 cm² (depending on the model)least 80-200 cm² (depending on the model)

c) position the mechanism (Fig. B) fl ush with the upper c) position the mechanism (Fig. B) fl ush with the upper

face of the fl oor, carefully sealing the points where face of the fl oor, carefully sealing the points where

outside air may leak d) make sure the damper moves outside air may leak d) make sure the damper moves

correctly (Fig. B)correctly (Fig. B)

e) with a hose clamp Ø 16-20 cm fi t a length of at least e) with a hose clamp Ø 16-20 cm fi t a length of at least

2 meters of stainless steel flue, with the fi tting for a Ø 2 meters of stainless steel flue, with the fi tting for a Ø

16 cm flue or the fi tting for a Ø 20 cm flue (Fig. C)16 cm flue or the fi tting for a Ø 20 cm flue (Fig. C)

f) wrap the section of steel pipe with a multilayeredf) wrap the section of steel pipe with a multilayered

ceramic fi bre mat or equivalent material (Fig. C)ceramic fi bre mat or equivalent material (Fig. C)

g) slip the section into the flue of the existing fireplace g) slip the section into the flue of the existing fireplace

and make sure the thickness of the ceramic fi bre and make sure the thickness of the ceramic fi bre

wrapping is suffi cient to completely fill the space wrapping is suffi cient to completely fill the space

between the new steel pipe and the existing flue (Fig. C)between the new steel pipe and the existing flue (Fig. C)

h) place Firebox® onto the mechanism (Fig.B) h) place Firebox® onto the mechanism (Fig.B)

checking that:checking that:

- the lower fl ange has been removed to allow the fl ow - the lower fl ange has been removed to allow the fl ow

of external air;of external air;

- The defl ector is open, using the knob located at the - The defl ector is open, using the knob located at the

top left on the front of Firebox®;top left on the front of Firebox®;

- a seam of high temperature mastic has been inserted - a seam of high temperature mastic has been inserted

where the flue attaches and on the smoke outlet collar;where the flue attaches and on the smoke outlet collar;

i) lower the previously inserted stainless steel pipe until i) lower the previously inserted stainless steel pipe until

it fi ts into the Firebox® smoke outlet collar.it fi ts into the Firebox® smoke outlet collar.

Do this by hand in the space between Firebox® and Do this by hand in the space between Firebox® and

the top of the inlet to the existing chimneythe top of the inlet to the existing chimney

l) if Firebox® is ventilated, leave a space for the fan l) if Firebox® is ventilated, leave a space for the fan

power cord making sure it does not come into contact power cord making sure it does not come into contact

with hot partswith hot parts

m) carefully close off the remaining space between m) carefully close off the remaining space between

Firebox® and the edges of the inlet to the existing Firebox® and the edges of the inlet to the existing

chimney.chimney.

It can be closed off with a metal mantelpiece, brickwork It can be closed off with a metal mantelpiece, brickwork

or fi re retardant plasterboard. or fi re retardant plasterboard.

Leave a slight space between the closing material and Leave a slight space between the closing material and

Firebox® to allow for expansion.Firebox® to allow for expansion.

INSTALLATION IN AN EXISTING FIREPLACEINSTALLATION IN AN EXISTING FIREPLACE

WITHOUT EXTERNAL AIR INTAKEWITHOUT EXTERNAL AIR INTAKE

Check for the possibility of making a pit inside the

existing fi replace (Fig. A) by removing the fi re surface.

This pit must be big enough to hold the external air

intake mechanism (Fig. A) and must be connected to

the outside by a duct with cross-sectional area of Ø

80/200 cm2 (according to model) (Fig. B).

If it is not possible to do as described above, place a

80/200 cm2 external air intake as near to Firebox® as

possible.

In this case, the mechanism is not used and the lower

Firebox fl ange must not be removed.

Proceed with the installation as described in

the previous section from point “e” onwards.

INSTALLATION WITH A NEW, SPECIALLYINSTALLATION WITH A NEW, SPECIALLY

MADE COVERINGMADE COVERING

Position Firebox® according to the characteristicsPosition Firebox® according to the characteristics

of the new covering with which it will be completed.of the new covering with which it will be completed.

If the covering is produced by EdilKamin, you will fi If the covering is produced by EdilKamin, you will fi

nd instructions for correctly positioning Firebox® in the nd instructions for correctly positioning Firebox® in the

packaging.packaging.

Place the external air-intake mechanism and connect Place the external air-intake mechanism and connect

the lower inlet directly with the outside using a fl exible the lower inlet directly with the outside using a fl exible

aluminium tube or a specially made duct; Both having aluminium tube or a specially made duct; Both having

a minimum cross-sectional area of 80-200 cm2 (Fig. a minimum cross-sectional area of 80-200 cm2 (Fig.

B) (depending on model).B) (depending on model).

Place Firebox® onto the mechanism and make sure Place Firebox® onto the mechanism and make sure

the lower fl ange has been removed to allow the fl ow the lower fl ange has been removed to allow the fl ow

of external air (Fig. B).of external air (Fig. B).

Connect Firebox to the flue with a Ø 16 or Ø 20 cm Connect Firebox to the flue with a Ø 16 or Ø 20 cm

pipe. Complete with the chosen covering and install pipe. Complete with the chosen covering and install

the kits for hot-air circulation (see followingthe kits for hot-air circulation (see following

instructions).instructions).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Firebox Deco in the language / languages: English as an attachment in your email.

The manual is 1.13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Edilkamin Firebox Deco

Edilkamin Firebox Deco Usermanual and installation guide - English - 80 pages

Edilkamin Firebox Deco User Manual - German - 28 pages

Edilkamin Firebox Deco Usermanual and installation guide - German, French, Italian, Portuguese, Spanish - 80 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Edilkamin Firebox Deco Manual

Product: