Manual Edilkamin Double (page 16 of 62) (English, German, Dutch, French, Italian, Spanish)

810848

Zoom out

Zoom in

1/62

Note: The product is supplied with

two anti-corrosion discs (one on the

outside and one on the inside of the

combustion chamber). They must

be removed during unpacking and

disposed of as normal waste.

ENGLISH

Counterweights

Counterweights installation

The latch hatch is equipped with counterweights

which guarantee both the closure and a soft

movement.

The action of the counterweights can be

adjusted by adding one or more washers

(additional counterweights) provided with the

chimney.

The additional counterweights (washers) can be

mounted at any time without dismantling the

chimney shell.

PROCEDURE.

1. Completely close the latch hatch

2. Rotate the hatch slide blocking lever.( n 35 -

esploso page 63 )

Open the glass door, proceed as indicated at

page 21 , as, for example, is necessary for the

cleaning of the glass

3. unhook the support profiles, left and right, of

the ecokeram hearth walls

4. remove the ecokeram hearth walls

5. At this point, the closing lids of the

counterweights inspection compartment will

remain visible.

Remove the lids of the counterweights

compartments by unscrewing the four screws.

6. Loosen and remove the M8 screw of the

counterweight door bar.

7. From the bottom, add the additional

counterweights on the base counterweight bar,

and fix them with the M8 screw which had just

been removed.

The same number of additional counterweights

is to be mounted on both sides.

8. Remount the sheet lids and reposition the

hearths walls.

9. Re-hook the fixing plates of the hearths walls.

10. Close the glass door. Do not forget to rotate

the door closing lever with the appropriate

handle! )

11. Unblock the hatch by rotating the slide

blocking lever (n 6 page 21) and verify the

sliding.

12. The hatch must slide with a soft movement,

remaining balanced.

13. Eventually further adjust the sliding by

symmetrically removing or adding the additional

counterweights (washers).

Premise

•The DOUBLE hearth must be installed

keeping to the following instructions, as the

safety and plant efficiency depend on the

correct installation.

•Carefully read the present instructions

before mounting.

•EDILKAMIN declines any responsibility for

eventual damages deriving from the non

compliance with the present instructions

and, in case, any warranty right will be

void.

•The DOUBLE hearth is supplied already

assembled on non returnable pallet.The

internal covering of the hearth is supplied

already installed

•A model identification label is applied

under the hearth panel; the label can be

seen until the hearth is covered. The model

identification number is indicated in the

documentation supplied with the product.

External air inlet

The connection with the outside

section equal 120 cm2 useful

passage (ø 12.5 cm) is absolutely

necessary for the good functioning

of the hearth, it must therefore be

realised.

In case of use for long periods with

hearth open, a supplementary air

inlet of a further 120 cm2 useful

passages, must be provided.

The 125 mm fitting to be installed on one

of the two sides and below the hearth, must

be directly connected with the outside.

The connection can be realised with

aluminium flexible pipe, being careful to

seal the points where air loss may verify.

It is advisable to apply a protection grill

to the outside of the air inlet conduit, but

which must not reduce the useful

passage section.

The external air must be captured at floor

level (it cannot come from above).

• Whenever the air volume is scarce and

the type of building in which the chimney

is installed particularly air sealed, it will be

necessary to install a supplementary air inlet

of 120 cm2 as said above

Important warnings

As well as that indicated in the present

document, bear in mind the UNI rules:

- n. 10683 - wood heat generators:

installation requirements

- n. 9615/90 - calculation of the

chimney internal dimensions.

In particular:

- before starting any mounting

operation, it is important to verify the

compatibility of the plant as established by

the UNI 10683 rule in paragraphs 4.1/

4.1.1 / 4.1.2.

- once mounted, the installer must

“start up” the plant and issue the

documentation requested in the UNI

10683 rule, respectively in paragraphs

4.6 and 5.

Before installing the cover, verify

the correct functioning of the

connections, the controls and all

moving parts.

The veriﬁ cation must be carried

out with the chimney having been

on for a few hours, before covering the

hearth, in order to eventually intervene.

Therefore, the finishing operations such as

for example:

- manufacture of the false hood

- mounting of covering

- carrying out stripping, painting, etc.must

be carried out once tested with positive

result.

Therefore, Edilkamin does not answer for

burdens deriving from both demolition

and reconstruction interventions, even if

subsequent to replacing hearth pieces

which resulted faulty.

INSTALLATION INSTRUCTIONS

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Double in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0.93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Edilkamin Double Manual

Product: