Manual Edilkamin Blade H 15 (page 47 of 88) (English)

810902

Zoom out

Zoom in

1/88

ENGLISH

INSTALLATION

INSTALLER

FLUE

Further to the general prescriptions, the flue

must

• only be used to discharge smoke

• be correctly sized to satisfy the requirements of

smoke discharge (EN 13384-1)

• must preferably be insulated, in steel with a circular

internal section. If rectangular, the corners must

have a radius of not less than 20 mm, with a ratio

of the internal dimensions of <1.5

• must normally be at least 1.5 metres in vertical

length

• must have a constant cross section

• must be waterproof and thermally insulated to

ensure proper draught

• preferably provide a collection chamber for

unburnt residues and condensates

• if pre-existing, must be clean, to prevent fire

hazards

• in general, we recommend fitting a tube inside the

existing masonry chimney if its diameter is greater

than 150 mm. This recommendation is purely

indicative; the installer must assess the actual

situation on-site after measuring the draught.

Besides the general prescriptions, the buried system

must:

• operate in negative pressure;

• be inspectable;

• comply with local regulations.

must:

• be windproof

• have an internal cross-sectional area equivalent to

that of the flue and a smoke outlet at least double

that of the interior of the flue

• extend beyond the back flow zone (in Italy, refer to

UNI 10683 point 6.5.8.)

• allow for maintenance of the chimney

For dual flues (which should be spaced at least 2 m

apart), the chimney pot receiving the smoke from the

solid fuel appliance or the pot on the higher storey

must be at least 50 cm higher than the other

COMBUSTION AIR INTAKE

In general, we suggest two ways to ensure a proper

flow of combustion air. The air must be drawn from

outside*

Please remember to also ensure air exchange for

heating and glass cleaning air, etc.

Indirect air intake

The product draws air from outside through a hole in

the rear.

Install an air outlet at floor level with an effective sur-

face area (net of the screen or other protections) of at

least 80 cm2 (10 cm in diameter).

To prevent draughts, we recommend installing the

intake behind the product or behind a radiator.

Installing it in front of the appliance will create

unpleasant draughts.

Direct air intake **

Install an air intake of effective surface area (net of the

mesh or other protective equipment) equal to the cross

section of the air intake at the back of the product.

Connect the air intake to the appliance's air intake with

a pipe that may also be flexible. Increase the diameter

of the pipe if the pipe is not smooth: assess any load

loss.

We recommend not exceeding a 3 m length, taking

into account the flue draught. For each curve, up to a

maximum of two curves, the length should be reduced

by 1m. Assess whether or not to increase the diameter

of the pipe.

*The air may be drawn from an adjacent room only if:

• the flow is taken from permanent and unobstructed

openings communicating with the outdoors;

• the air pressure in the adjacent room is never

lower than that of the outdoor pressure;

• the adjacent room is not a garage, subject to fire

hazard, a bathroom or a bedroom;

• the adjacent room is not a shared room in the

condominium.

In Italy, UNI 10683 provides that ventilation is sufficient

even if a pressure difference between the outdoors

and indoors of no more than 4 PA is guaranteed (UNI

EN 13384-1). The installer who issues the declaration

of conformity is responsible for ensuring these

conditions.

**Direct connection to the air intake will not make the

product airtight. It is therefore necessary to additionally

ensure an air intake from within the room where the

product is installed (i.e. for cleaning the glass)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin Blade H 15 in the language / languages: English as an attachment in your email.

The manual is 4.2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Edilkamin Blade H 15

Edilkamin Blade H 15 Usermanual and installation guide - German - 88 pages

Edilkamin Blade H 15 Usermanual and installation guide - French - 88 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Edilkamin Blade H 15 Manual

Product: