Manual Edilkamin AQUAMAXI 28 (page 31 of 182) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish)

810928

Zoom out

Zoom in

1/182

- 31 -

ENGLISH

Fig. 1/a

The fundamental characteristics of the chimneypot are:

- an internal cross-section at the base, which is the same as that

of the chimney À ue.

- an outlet cross-section which is no smaller than twice that of

the chimney À ue.

- its position must be high enough to catch the wind and avoid

downdraft areas in turbulent wind.

In addition to that mentioned above, please consider the

indications stipulated in UNI 10683/2005 standard, para-

graph 4.2: “connection to the smoke outlet system” and its

subsections.

- Use a stainless steel À ue to connect the thermo ¿ replace to the

chimney À ue, adhering with the diameters indicated in the spe-

ci¿ cations table and the guidelines given in the chapter called

“chimney À ues”.

- Verify that all moving parts function properly before setting

the thermo ¿ replace covering in place.

- This system must be tested and ignited for the ¿ rst time

before the covering is set in place.

The base of the thermo ¿ replace covering must allow the

internal air to be recycled. Therefore, suitable slots or apertures

must be made for the air to pass through. Parts of the thermo

¿ replace covering that are made of marble, stone and bricks

must be mounted with a small gap between them and the ¿ re-

place so as to prevent possible breakage due to expansion and

excessive overheating.

Protect wooden parts with ¿ reproof materials.

Fireproof parts of the covering (beams or frames) must not be

in contact with the ¿ replace unit but must be at least 1-2 cm

away to allow a À ow of air that prevents heat accumulation (see

Fig. 1/a).

The housing compartment must be made of masonry or ¿ repro-

of materials and must not have combustible elements inside.

The ¿ replace mantel can be made of ¿ reproof plasterboard

panels or gypsum board and, however, of completely ¿ reproof

material. Air should be allowed to À ow inside the ¿ replace

mantel (through the gap between the door and the beam).

Through convective motion, the air will À ow out from the grille

installed at the top, resulting in heat recovery and preventing

excessive overheating (See Fig. 1/a).

The ¿ replace mantel must have appropriate openings to carry

out maintenance on the ¿ ttings.

In addition to that mentioned above, please consider the in-

dications stipulated in the UNI 10683 standard, paragraphs

4.4 and 4.7: “insulation, ¿ nishing, ¿ replace covering and

safety recommendations”.

Insulating mats must be applied when using an installation

KIT so as to protect it from the heat radiation emitted by

the thermo ¿ replace.

45°

max.45°

inspection

CHIMNEY FLUES AND CHIMNEYPOT

The thermo ¿ replace smoke outlet has a circular crosssection

so that stainless steel pipes can be used. If the chimney À ue

inlet is not vertically above the thermo ¿ replace, the connection

from the ¿ replace to the À ue must not have a narrowing

section or inclinations greater than 45° (¿ g. 1-2-3-4).

The ¿ replace unit must not be connected to a shared À ue.

The fume section must be inspectable and installed in such a

way that it can be cleaned (use inspectable TEEs).

If the chimney À ue is not brand new or too big, it is recommen-

ded to ¿ t in stainless tubes of an appropriate diameter and with

suitable insulation.

If the chimney À ue is installed outside, it is recommended to

use an insulated, double walled, stainless steel À ue.

The characteristics of the construction must be suitable to

withstand a smoke temperature of at least 450° C, with parti-

cular reference to the mechanical resistance, insulation and the

gas tight sealing.

The À ue must be certi¿ ed under EN 1856.

The junction of the steel À ue inlet and the smoke outlet of the

¿ replace must be sealed with high temperature mastic.

Have quali¿ ed personnel clean the À ue once a year.

INSTALLATION

INSTALLATION COVERING, FIREPLACE

MANTEL

If combining with a pre-fabricated Edilkamin covering, to de¿ -

ne the exact positioning of the thermo ¿ replace, it is important

to take the chosen covering model into consideration.

The positioning is implemented according to the model chosen

(refer to the installation instructions found inside the packaging

of each thermo ¿ replace covering).

Always ensure the thermo ¿ replace is level during the installa-

tion process.

- Drill a hole into the wall or the À ooring for the external air

intake and connect the air adjustment mechanism to the hole as

described in the chapter called “external air inlet”.

Hot air ŏ ow

grille

Mantel

Door slider

guide

Metal mantel

Hood

Wooden

beam

Front part

Air inlet in the

mantel

sliding door

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin AQUAMAXI 28 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 5.98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Edilkamin AQUAMAXI 28 Manual

Product: