Manual Edilkamin ANIA (page 37 of 192) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

672465

Zoom out

Zoom in

1/192

- 39 -

ENGLISH

Changing pellet loading (with self-regulation deactivated)

When the “M” key on the radio control is held down for two

seconds and the display is scrolled using the “+” and “–” keys,

you come across the “User’s Menu”. When this is con¿ rmed

the display reads “ADJ-PELLET ; ADJ-DRAUGHT and RA-

DIO MENU” (CAT). The pellet drop can be adjusted manually

by changing the capacity in percentage terms (+/- 30 %).

By con¿ rming this function with the menu key, you can access

the function to adjust pellet loading. By decreasing the

value set, pellet loading is decreased. By increasing the value

set, pellet loading increases. This function is useful if

changing the pellet type for which the stove has been calibrated

and loading therefore needs correcting.

Should this correction not suf¿ ce, contact the Edilkamin-autho-

rised Dealer, to establish the new operating axis.

Notes on À ame variability

Flame status may vary depending on the type of pellet used,

in addition to normal solid fuel À ame variability and regular

combustion chamber cleaning carried out automatically by the

boiler.

(N.B.: which does NOT replace necessary cold suction by the

user prior to ignition).

RESERVE WARNING

The stove is ¿ tted with an electronic function that detects the

residual quantity of pellets in the tank.

The detection system is integrated into the electronic board,

allowing you to see how many hours and kg are left until

pellet exhaustion, at all times. For correct system function, it is

important that the following procedure is followed during the

¿ rst ignition (by the Dealer).

This provides a reference indicator. Greater precision is

obtained by regularly zeroing the system before ¿ lling it again.

Edilkamin does not accept any responsibility for differences

from what is indicated (which may be due to external factors).

Pellet reserve system

Before enabling the system, you need to load a sack of pellets

into the tank and use the stove until the loaded

fuel has run out. This allows for a short system road test.

After this, the tank can be ¿ lled completely and the stove

started up.

When running, at the time at which a whole 15 kg sack of pel-

lets can be loaded, the display will show the word

“Reserve” À ashing.

At this point, after having poured in a sack of pellets, you need

to ‘inform’ the memory that you have loaded 15 kg.

To do so, proceed as follows:

1. press the “M” key (for approximately 3-4 seconds) until the

word “Clock” appears.

2. press the “+” key until the word “Reserve” appears.

3. press the “M” key until the following screen appears,

then use the “+” key to take the ¿ gure (*) to the value equal to

the Kg of pellets loaded (15 kg in the above example).

4. press the “M” key to con¿ rm

5. press the key

to exit.

After having completed the above procedure, after having con-

sumed the 15 kg, the wording “Reserve” will appear

À ashing at intervals. After which the operation must be repea-

ted, from point 1 to point 5.

SIMPLIFIED LIGHTING BUTTON

If the remote control device does not work, you can carry out

the basic functions by means of a red emergency button posi-

tioned on the left side of the stove (see Fig. g. 1).

Push this button once or more times to activate the required

function:

1. STOVE OFF

by pressing the red button for 2 seconds this turns on.

2. STOVE ON

by pressing the red button for 2 seconds this turns off.

3. STOVE ON

manual mode, by pressing the red button, you go from P1 to

P3.

4. STOVE ON

automatic mode, by pressing the red button, you go from 5°C

to 30°C.

Kg remaining in tank

Kg loaded

INSTRUCTIONS FOR USE

simpliŎ ed lighting

button

¿ g. 1

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin ANIA in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Edilkamin ANIA Manual

Product: