Manual Edilkamin ANIA (page 36 of 192) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

672465

Zoom out

Zoom in

1/192

- 38 -

ENGLISH

INSTRUCTIONS FOR USE

Filling the cochlea.

The ¿ rst time you use the product, or should the tank be com-

pletely emptied of pellets, to ¿ ll the coclea press both keys “+”

and “–” on the remote control at the same time, holding for a

few seconds. As you release the keys, the display should show

the wording “LOAD”. This should be carried out before igni-

tion if the stove has stopped due to having run out of pellets,

at the end of operation to empty the combustion pot before

turning.

It is quite normal for some pellets to remain, that the cochlea

cannot suction.

Automatic igniting.

With the stove on stand-by, press and hold the key

, on the

remote control for 2 seconds. This will start-up the

ignition procedure, showing the wording “START”. At the

same time, a countdown in seconds begins (from 1020 to 0).

Ignition is not at a preset time, however: its duration is automa-

tically shortened if the board reports that certain tests have

been passed. The À ame appears after about 5 minutes.

Manual igniting.

Temperatures of below 3°C will not allow the electrical resi-

stance to heat suf¿ ciently. In this case, or should the

resistance be temporarily out of action, Diavolina® type ¿ re-

starters can be used.

Insert a piece of lit Diavolina into the combustion chamber,

close the door and press

the remote control.

POWER REGULATION

• Remote control manual operation

With the stove working, press the key “M” on the remote con-

trol once. The display will show the word “POWER P”.

(specifying the power at which the insert is working). Press the

keys “+” or “–” to increase or decrease the insert’s

working power (from “POWER P1” to “POWER P3”).

• Remote control automatic operation

Press key “A” to switch to automatic operation, adjusting the

temperature desired for the room (use the “+” and “–” keys

to set the temperature from 5°C to 35°C, and the stove will

regulate working power required to reach the temperature set.

If a temperature below that of the room is set, the insert will

stay on “POWER P1”.

Turning off

With the stove running, press and hold the key

rom the re-

mote control for 2 seconds. The turn-off procedure will begin,

showing a countdown on the display from 9 to 0 (for a total of

10 minutes).

The turn-off phase involves:

• Interruption of pellet supply

• Maximum ventilation

• Smoke expulsion motor

Never pull the plug out whilst the device is still in the process

of turning off.

OPERATIONS THAT CAN ONLY BE CARRIED OUT BY

REMOTE CONTROL

Clock regulation

Press and hold the key “M” for 2 seconds to access the “Clock”

menu. This allows you to set the internal electronic board

clock. By then pressing the key “M”, the following data appe-

ars in sequence and can be regulated:

day, month, year, hour, minutes, day of the week.

The wording “SAVE??” will appear for con¿ rmation with “M”.

This will allow you to check that the operations performed are

correct, prior to completion (the wording “SAVE” will then be

shown on the display).

Operations for switching on, switching off and regulating

power can be carried out by means of the red emergency button

placed on the back of the stove (see page 39).

Weekly timer

Press and hold the “M” key on the remote control for 2 secon-

ds. This turns on the clock regulation and by pressing the ‘+’

key, the weekly timer function is accessed, with the display

showing the description “PROGRAMM ON/OFF”.

This function allows you to select the type of programming,

which allows a maximum of three ignitions to be set.

As you con¿ rm the display with the key “M”, one of the fol-

lowing options will appear:

NO PROG. (no programme set)

DAILY PROGRAM (single programme for every day of the

week)

WEEKLY PROGRAM. (speci¿ c programme for each day

individually)

Use the “+” and “–” keys to switch between programmes.

Con¿ rming by pressing the “M” key “DAILY PROGRAM.”

and pressing the “+” key, the choice of the number of program-

mes (ignition/extinguishing) per day can be made.

Use the “DAILY PROGRAM” to set identical programme/s for

every day of the week.

By then pressing the “+” key, the following can be seen:

- Prog. no.

- 1st prog. (one turn on and one turn off per day), 2nd prog.

(identical), 3rd prog. (identical)

Use the “–” key to show in reverse order.

If the 1st programme is selected, the turn on time is shown.

The display shows: 1 “ON” at 10 Use the “+” and “–” key to

change the hour. Con¿ rm with the “M” key (All 1 On/Hour

10).

The display shows: 1 “ON” at 30 Use the “+” and “–” key to

change the minutes. Con¿ rm with the “M” key (1 Off min).

The same applies for the turn-off time to be set and for subse-

quent turning on and off.

Con¿ rm by pressing “M” and the wording “SAVE??” will

appear on the display.y.

When con¿ rming ”WEEKLY PROGRAM”, you will need to

choose the day to which the programming is to apply:

7 Sat; Progr.1; 1 Mon ; 2 Tues; 3 Wed; 4 Thurs; 5 Fri; 6 Sa;

Once the day is set, use the keys “+” and “+” and con¿ rm by

pushing the “M” key to choose 1 to 3 ignitions, to programme

in the same way as for the “DAILY PROGRAM”, choosing

whether or not to enable a programme for each day of the

week, and if so choose the number of interventions and at what

times.

Should you make an error during programming, you can leave

the programme without saving. As you press a key,

, the

display will show the word “no SAVE”.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Edilkamin ANIA in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Edilkamin ANIA Manual

Product: