663877

EdgeCraft ScissorPro 500 Manual

5
Zoom out
Zoom in
Previous page
1/8
Next page
4. During the sharpening process, you will be asked to feel for a burr on the scissors blade
in order to know when sharpening is complete. It is essential that you understand how this
is done.
Feeling for a burr involves running your finger carefully across (NOT ALONG) the back of the
blade as shown in Figure 5. A burr is a microscopic protrusion of metal produced during the
sharpening process under the edges of the blade that can be felt but is not always visible. It
will feel rough and jagged compared to the smooth finish of the back of the blade.
5. Your ScissorPro
®
will sharpen either right hand or left hand scissors without any need to
disassemble them. If you are left handed, you probably have purchased left hand scissors.
To sharpen right hand scissors, turn the sharpener so you face the switch side of the
ScissorPro
®
(see Figure 6). To sharpen left hand scissors, you should face the opposite side
of the sharpener (see Figure 7). From this point onward, these instructions are written as they
apply to right hand scissors.
6. Before you turn on your ScissorPro
®
, take a minute to get the feel of the Magne-Flex
™
hold-down system and to learn how to insert a blade into the sharpener. Select a blade and
insert it—cutting edge first—under the fingers of the hold-down spring of the FINE sharpening
slot using the grip shown in Figure 6. If inserted correctly, the blade being sharpened is the top
blade, and the free blade will be hanging below the blade being sharpened.
Practice inserting the scissors blade under the hold-down spring, as close to the scissors
pivot as feels comfortable and pulling the blade smoothly toward you. Feel the effect of the
magnet and hold-down spring as they establish the sharpening angle for you. Light pressure
is required to slide the blade down the magnet slope and underneath the hold-down spring
as the blade approaches the diamond sharpening disk. Allow the Magne-Flex
™
hold-down
system to control the sharpening angle for you. It is also important to prevent the free blade
(that is the one not being sharpened) from hitting the sharpener in a way that might influence
the sharpening angle. It is convenient to stabilize the free blade using your forefinger and
thumb as shown in Figure 6. Turn over the scissors and repeat with the other blade.
7. Generally, most scissors can be sharpened by using only the FINE stage (Figure 1). The highly
efficient diamond abrasive used in the ScissorPro
®
will quickly develop a superbly sharp edge.
The COARSE stage sharpens at a larger angle using somewhat large diamonds.
5
Figure 7. Suggested hold for left hand scissors. Figure 6. Suggested hold for right hand scissors.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EdgeCraft ScissorPro 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EdgeCraft ScissorPro 500 in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info