663876
8
Zoom out
Zoom in
Previous page
1/12
Next page
8
RESHARPENING
Normally you can resharpen rapidly with 3-5 pairs of alternating pulls through Stage 2 only.
You will be able to resharpen 3-5 times just in Stage 2 before having to sharpen again in
Stage 1. You may find it easier and faster to sharpen using Stage 2 for all resharpening
rather than using a sharpening steel for periodic touch-up of the edge. Periodically,
however, you will find it necessary to resharpen first in Stage 1 followed by Stage 2 in
order to develop the shaving-sharp edge that should be created in Stage 2.
If a traditional sharpening steel is used repeatedly to tune up the edge between
resharpenings on the Chef’sChoice
®
Model 2000, you will have to resharpen first in
Stage 1, following the normal sharpening procedure and then hone in Stage 2. In this case
it will take 3 or more alternating pairs of pulls in Stage 1 to achieve a uniform burr before
proceeding to Stage 2.
In view of this, if you wish to improve productivity and reduce sharpening time, you should
avoid using the traditional sharpening steel and rely on Stage 2 for fast resharpening.
Make sure the knife is free of food, fat or oil before resharpening in Stage 2.
SERRATED KNIVES
While the Chef’sChoice
®
Model 2000 is designed primarily for non-serrated knives, it will
significantly improve the performance of serrated knives by honing the tips of the
serrations. Two or three pairs of pulls, alternating through the left and right slots of Stage 2
(Honing) should be sufficient.
Caution: Do not use Stage 1 on serrated knives!
REMOVING, CLEANING AND INSERTING THE SHARPENING MODULE
When there is evidence of grease, fat, or food on any of the sharpening wheels or on the
Sharpening Module where it cannot be readily removed, it is time to wash the module
as described in the following section. We recommend knives always be cleaned before
sharpening – at a minimum, wipe them down with a cloth in order to reduce the need for
frequent cleaning of the Sharpening Module.
To remove the Sharpening Module, first make sure the motor switch is in the “OFF”
position. Then press the release button while pulling the Sharpening Module away from
the motor housing (see Figure 8.) The Sharpening Module should remove easily.
Figure 8. Sharpening Module is easily removed
for cleaning.
Press release button
and pull Sharpening
Module to right
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EdgeCraft Chef-s Choice - Commercial 2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EdgeCraft Chef-s Choice - Commercial 2000 in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info