663876

EdgeCraft Chef-s Choice - Commercial 2000 Manual

4
Zoom out
Zoom in
Previous page
1/12
Next page
4
DESCRIPTION - MODEL 2000 SHARPENER
The Model 2000 sharpener uses a novel two-stage sharpening and honing process, where
the knife is first sharpened with a pair of conical diamond-coated wheels and then honed
with a pair of patented conical honing disks incorporating ultrafine abrasive particles. This
creates a unique edge geometry that gives the edge extraordinary “bite” and sharpness
and ensures it will stay sharp much longer than conventionally sharpened knives. The
Sharpening Module, incorporating both the sharpening and honing stages, is a self-con-
tained unit that can be removed for washing and sanitizing in a dishwasher or at the sink. It
can be removed simply by depressing the release button (Figure 2) and sliding the module
off the motor-drive section.
A powerful 150 watt motor operating at 1700 RPM is enclosed in the motor housing.
Splined drive couplings attached to the shafts of the motor drive and the Sharpening
Module permit their rapid engagement or disengagement.
In both the sharpening and honing stages, the edge must be sharpened on alternate
strokes in the right and left slots (see Figure 3). Precise “Blade Guides” position and align
the knife at the correct angle while plastic hold-down springs stabilize and secure the
blade as it is pulled through each slot and makes contact with the abrasive wheels. The
downward movement of the blade in each of the slots is limited and controlled by an Edge
Stop Plate (Figure 3), made of a high-density polymer that serves both as a stop and as
a micro-guide “slot” for the edge, without damaging the sharp edge being formed. There
are Edge Stop Plates at the front and rear of the sharpening and honing stages. For best
results, the knife edge should only just touch or lightly rest on the front Edge Stop Plate.
Excessive downward pressure is unnecessary and will result in excessive cutting of the
Edge Stop Plate. The edge need not rest on the rear Stop Plate for the entire sharpening
and honing stroke.
Figure 3. Knife is inserted between the Blade Guide
and the plastic spring until edge rests lightly on Edge
Stop Plate.
Plastic Spring
Edge
Stop Plate
Knife Blade
Guide
Figure 2. Sharpening module is inserted on rails
and slid toward the motor-drive section to engage
motor-drive. To disengage, press release button and
slide away from the motor-drive. See text.
Sharpening Module
Motor-drive Section
Release Button
Knife Blade Guides
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EdgeCraft Chef-s Choice - Commercial 2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EdgeCraft Chef-s Choice - Commercial 2000 in the language / languages: English as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info