580132
8
Zoom out
Zoom in
Previous page
1/9
Next page
UN PROBLEME ?
10
N’hésitez pas à nous appeler sur notre ligne d’assistance téléphonique (tel en fin de notice).
Nos techniciens se feront un plaisir de vous aider à parfaire votre installation.
him/her to listen into what is happening on
your side through the microphone & speaker
on the unit.
The Communication channel, once opened,
lasts for 3 minutes. The recipient will hear
repeated beep sound 15 second before the
Dialer hangs up the line.
If the recipient wants to have more time to
listen, he can press the "1" button on his
telephone set again to add another 3 minutes.
<
<
N
N
O
O
T
T
E
E
>
>
When the two ways communication
channel are opened, the Control Panel
will then stop the audible alarm to
allow
speech communication.
4. Terminating the Two Way
Communication
After two-way voice communication has been
initiated, the recipient can terminate the
communication by sending DTMF "0" or “9”
signal.
Terminating by signal “0”
If DTMF 0 signal is received, the two way
voice communication will terminate. Dialer will
continue to dial the next phone number and
activate the Control Panel Siren.
Terminating by signal “9”
If DTMF 9 signal is received, the two-way
voice communication will terminate. The Dialer
will cancel any further dialing and leave the
Control Panel Siren off as it is.
<
<
N
N
O
O
T
T
E
E
>
>
In any case, if the two-way voice
communication is not terminated by the
recipient, the Dialler will automatically go
on-hook as it is terminated by signal "0"
within 3 minutes of voice communication
time period.
5. Incoming Call
Step 1. Dial HA2000RTC, listen to 2 dial tones
and hang up
Step 2. Wait between 10s and 30s and dial
again.
Step 3. Listen to 2 beeps from the receiver.
Step 4. Press PIN Code (0000) and if the
operations were successful dialer will
hear a long beep
Step 5. Press the following numbers on the
phone to activate specific functions:
Press “1“ to activate 2-way communication.
Listen to 3 beeps.
Press “2“ to activate Arm Mode. Listen to
two beeps from the reciever. The Control
Panel will perform a long beep.
Press “3’ to activate Disarm Mode. Listen to
a beep from the receiver. The Control Panel
will sound two beeps
Press “9” or “0” to disconnect. Listen to 5
beeps from the receiver.
<
<
N
N
O
O
T
T
E
E
>
>
During incoming call if the Control Panel
HA2000 activates an alarm, Dialer will
do 6 beeps and will immediately
disconnect the phone line. Then the
HA2000RTC prepares for reporting.
If Dialer have not learnt in from the
Control Panel or HA2000SOS, the
function to Arm or Diarm from phone is
disabled.
How to install the Auto
Dialer
The Dialer can be mounted on the wall or placed on
the tabletop.
Wall mount
The easiest way to get to know the system
and get it up and running quickly is to get all
the devices and accessories programmed on
a tabletop before locating and mounting them.
The Control Panel can be mounted on the wall or
wherever desired. Ensure the Control Panel is
fitted at approximately chest height where the
display can be easily seen and the keypad
convenient to operate.
Find a suitable location for the Auto Dialer to be
installed.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eden HA2000 RTC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eden HA2000 RTC in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eden HA2000 RTC

Eden HA2000 RTC User Manual - German - 9 pages

Eden HA2000 RTC User Manual - Dutch - 10 pages

Eden HA2000 RTC User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info