580132
7
Zoom out
Zoom in
Previous page
1/9
Next page
UN PROBLEME ?
9
N’hésitez pas à nous appeler sur notre ligne d’assistance téléphonique (tel en fin de notice).
Nos techniciens se feront un plaisir de vous aider à parfaire votre installation.
<
<
N
N
O
O
T
T
E
E
>
>
Correct the distance range to allow the
Dialer to be within the transmission range
of the Control Panel if Dialer is
unresponsive to the signal.
If no signal is received in 3 minutes, the
Auto Dialer automatically exits Test mode
and returns to Normal mode
Operation
1. Auto Dialing
Upon receiving the signal from the Control Panel,
the Auto Dialer will dial out and play the
appropriate message to summon help.
If no message or no telephone number is stored,
the Dialer will not dial to report.
When only one telephone number is stored
and that number is engaged, the Dialer will
automatically redial that number up to
maximum of 5 times with an interval of 62 sec.
between dialing attempts.
When two or more telephone numbers are stored,
the Dialer will dial in accordance to the Priority
Order Number. If the number being dialed is
engaged, it will try the next number.
Each phone number will be tried for maximum
rotation of 5 times with an interval of 5 seconds
between each phone number.
After dialing a phone number and the line is not
engaged, the Dialer will automatically play the
appropriate message for 80 seconds.
If a certain type of alarm occurred without the
corresponding message recorded, the Dialler will
play the subsequent message.
When the Auto Dialler has received 2 successful
acknowledgements from the recipients, it will stop
dialling.
<
<
N
N
O
O
T
T
E
E
>
>
When each phone number is dialed 5
times without any acknowledgement,
Failure status is reported and the
Dialer returns to Normal Mode with a
fault warning beep and Yellow LED
flashing every 3 seconds to remind the
user.
Only during diallings, if the Dialler
receives a Disarm signal from the Control
Panel, the Dialler will ignore it and
continue the dialing process.
While dialling, if PIN code (0000) and
CLRare pressed, you will hear a long
beep, the Dialler stops any reporting
immediately and for HA2000RTC, it will
also send a Disarm signal to the Control
Panel.
2. Call Acknowledgment
If the recipient successfully receives the call, he
should acknowledge it by pressing the “9”, “0”, or
“1” button on his telephone set:
Acknowledging with signal “9”
If the recipient presses “9” on his phone set as the
acknowledging signal, he will hear a long beep.
The Dialler will then take the following actions.
The Dialler will cancel all auto dialling.
Acknowledging with signal “0”
If the recipient presses “0” on his phone set as the
acknowledging signal, he will hear a long beep.
The Dialler will then take the following actions.
The Dialler will go back on-hook.
The Dialler will accept this successful
acknowledgment and continue to dial the
next phone number.
Acknowledging with signal “1”
If the recipient presses “1” on his phone set as the
acknowledging signal. The Dialler will then take
the following actions.
For HA2000RTC:
The Dialler will open the Two Way
Communication Path. Please see “Two Way
Voice Communication” in next section for
details.
The Dialler will accept this signal as
successful acknowledgement.
3. Opening the Two Way Communication
HA2000RTC only
HA2000RTC, after sending the alarm
message and receiving a DTMF 1 signal
from the recipient, will open up the Two Way
Voice Communication immediately.
The Two Way Voice Communication channel
enables you to talk to the recipient and permit
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eden HA2000 RTC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eden HA2000 RTC in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eden HA2000 RTC

Eden HA2000 RTC User Manual - German - 9 pages

Eden HA2000 RTC User Manual - Dutch - 10 pages

Eden HA2000 RTC User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info