388952

Economy hdm 1015 ebf 850k Manual

6
Zoom out
Zoom in
Previous page
1/22
Next page
Ferm 39
DK
06 Ferm
GB
Defects
The machine should be regularly inspected for
the following possible defects, and repaired if
necessary
.
• Damage to power cord
• Broken on/off trigger assembly.
• Short circuiting.
• Damaged moving parts.
Trouble shooting
1
When switched on, the motor does not turn.
• Failure in power supply.
• Check the power supply.
• Poor contact in the on/off trigger.
• Repair or replace the trigger assembly.
• Mains voltage too low.
• Extension lead too long, or too light.
• Damaged motor.
• Have your machine repaired by an expert.
• Carbon brushes worn.
• Replace the carbon brushes
2 Motor generates excessive noise, and runs
too slowly or not at all.
• Motor is overloaded due to excessive pressure
or drilling depth.
• Reduce the pressure or drilling depth, reduce
power
.
• Damaged motor.
• Have your machine repaired by an expert.
• Supply voltage too low.
• Adjust the supply voltage.
• Carbon brushes worn.
• Replace the carbon brushes
3 Overheating in the transmission case.
• Overloading of machine, or blunt drill bit
• Reduce the loading, or hone the drill bit.
• Reduced voltage.
• Adjust the supply voltage.
4 Heavy sparking from the motor.
• Inspect the carbon brushes for wear
.
Replacing carbon brushes
• Replace both carbon brushes at the same time.
• Regularly check the carbon brushes for wear
and defects.
•
Always replace worn-out carbon brushes.
• Always keep the carbon brushes clean, and
make sure that neither brush is obstructed.
• Open the machine to inspect/replace the car-
bon brushes.
• Remove and replace the carbon brushes if
necessary.
• Reassemble the rear handgrip.
Cleaning
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that
the ventilation openings are free of dust and dirt.
Remove very persistent dirt using a soft cloth
moistened with soapsuds. Do not use any sol-
vents such as gasoline, alcohol, ammonia, etc.
Chemicals such as these will damage the synthe-
tic components.
Lubrication
Regularly grease the hammer drill shaft.
Faults
Should a fault occur, e.g. after wear of a part, ple-
ase contact the service address on the warranty
card. In the back of this manual you find an explo-
ded view showing the parts that can be ordered.
Environment
To prevent damage during transport, the applian-
ce is delivered in a solid packaging which con-
sists largely of reusable material.
Therefore plea-
se make use of options for recycling the packa-
ging.
Faulty and/or discarded electrical or
electronic apparatus have to be collec-
ted at the appropriate recycling loca-
tions.
Warranty
For the conditions of warranty, please refer to the
separately provided warranty card.
Udskiftning ad kulbørster
• Udskift begge kulbørster samtidig.
•
Kontroller regelmæssigt kulbørsterne for slitage
og defekter.
• Udskift altid slidte kulbørster.
• Hold altid kulbørster rene og sørg for, at ingen
af børsterne er blokeret.
• Åben maskinen for at inspicere/udskifte kulbør-
sterne.
• Fjern og udskift kulbørsterne om nødvendigt.
• Monter det bageste håndtag igen.
Rengøring
Rengør regelmæssigt maskinhusene med en
blød klud, helst efter hver brug. Sørg for
, at venti-
lationsåbningerne er fri for støv og snavs. Fjern
vedholdende snavs ved hjælp af en klud, der er
fugtet med sæbelud. Brug aldrig opløsningsmid-
ler, som f.eks. benzin, sprit, salmiak osv., da
sådanne kemikalier beskadiger de syntetiske
dele.
Smøring
Smør regelmæssigt borehammerens aksel.
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en
enhed, kontakt venligst serviceadressen på
garantibeviset. På bagsiden af denne manual fin-
der du en tegning med alle dele, der kan bestil-
les.
Miljø
For at undgå transportbeskadigelse leveres mas-
kinen i en solid emballage. Emballagen er så vidt
muligt lavet af genbrugsmateriale. Genbrug der-
for emballagen.
Defekte og/eller kasserede elektriske
eller elektroniske maskiner skal aflever-
es på en genbrugsplads.
Garanti
Se venligst garantibetingelserne på garantikortet,
som er vedlagt separat.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Economy hdm 1015 ebf 850k at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Economy hdm 1015 ebf 850k in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 2,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info