Manual Economy by Ferm HDM1012 - FEBH-620KS (page 5 of 20) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

763924

Zoom out

Zoom in

1/20

Ferm 05

Electrical safety

Always check that the mains voltage is

the same as on the type plate of the

machine.

The machine is double insulated; there-

fore, no earth connection is required.

Replacement of power cords or plugs

Immediately dispose of old cords and plugs once

they have been replaced. It is dangerous to plug

a loose power cord into a mains power socket.

Use of extension leads

Only ever use approved extension leads that are

suitable for the power rating of the machine. The

minimum core thickness is 1.5 mm2. Whenever

using a reel extension lead, always fully unroll

the lead.

3. OPERATING

Hammer drills require very little operator

pressure. Excessive pressure on the tool

can lead to unnecessary overheating of

the motor, and burning of the driven tool.

Auxiliary handgrip

The auxiliary handgrip can be rotated 360º

around the drill head, enabling safe and comforta-

ble operation, for both left and right-handed users.

• Loosen the handgrip by turning it anticlockwise.

• Rotate the handgrip to the desire position.

•Retighten the handgrip in the new position.

Exchanging and removing drill bits

Fig. A + B

Before exchanging bits, first remove the

power plug from the wall socket.

Inspect bits regularly during use. Blunt

bits should be re-sharpened or repla-

ced.

•Lightly lubricate the shaft of the drill bit before

inserting into the machine.

•Place the shaft of the drill bit into the opening of

the drill chuck and twist until latched.

• To release and remove the drill bit pull back the

collar of drill chuck .

Setting depth gauge

• Loosen the handgrip by turning it anticlockwise.

•Insert the depth gauge ruler through the hole in

the auxiliary handgrip.

• Slide the ruler to the desired depth.

• Retighten the screw firmly.

Function selection switch

Fig. D

The correct position of the selection switch for

each machine function is given in the diagram on

page 3.

1 = Demolition hammer/chisel

2 = Rotary hammer drill

3 = Drilling

Switching On/Off

• To start the drill, squeeze the trigger.

• To stop the drill, release the trigger.

Installing dust catcher

Fig.C

The dust catcher prevents large amounts of dril-

ling dust entering the machine when drilling into

ceilings.

•Remove the drill bit.

• Slide the dust catcher over the shaft of the drill

bit.

• Place the drill bit with catcher in the drill chuck.

• Always replace a damaged dust catcher imme-

diately.

4. MAINTENANCE

Take care that the machine is not con-

nected to power whenever maintenance

work on the mechanical parts is taking

place.

The machines are designed to function problem-

free for a long period with a minimum of mainte-

nance. Through regular cleaning and correct tre-

atment, you help assure a long working life for

your machine.

Defects

The machine should be regularly inspected for

the following possible defects, and repaired if

necessary.

36 Ferm

ROTERENDE BOREHAMMER

Tallene i den følgende tekst korresonderer

med afbildningen på side 2 - 3.

Læs denne betjeningsvejledning nøje,

før maskinen tages i brug. Sørg for at

vide, hvordan maskinen fungerer, og

hvordan den skal betjenes. Vedligehold

maskinen i overensstemmelse med

anvisningerne, og sørg for, at maskinen

fungerer korrekt. Opbevar denne vejled-

ning og anden vedlagt dokumentation

sammen med maskinen.

Påtænkt anvendelse

Roterende borehammer anvendes til at bore hul-

ler i materiale som sten, beton og lignende mate-

rialer. Udstyret med de korrekte typer bor kan

maskinen også anvendes til at bore huller i træ

eller metal. Maskinen kan desuden anvendes

som mejselhammer i forbindelse med nedbryd-

ningsarbejde. Maskinen må ikke anvendes til

andre formål.

Undersøg venligst maskinen og tilbehøret for

transportskader.

Indhold

1. Information om maskinen

2. Sikkerhedsanvisninger

3. Betjening

4. Vedligeholdelse

1. INFORMATION OM

MASKINEN

Tekniske specifikatione

Produktinformation

Fig. A

1. Regulering af rotationshastighed

2. On/Off-kontakt

3. Håndtag

4. Hammerfunktion

5. Kulbørstehætte

6. Elektrisk ledning

7. Støttehåndtag

8. Dybdemåler

9. Støvfilter

10.Bor

11.Sikkerhedsmuffe

2. SIKKERHEDSANVISNINGER

I denne betjeningsvejledning er anvendt følgende

symboler:

Betegnelse for risiko for personskader,

dødsfald eller beskadigelse af værktøjet

i tilfælde af at du er uopmærksom på

instruktioner i denne manual.

Indikerer farer for elektrisk stød

Brug beskyttelsesbriller og høreværn

Specifikke sikkerhedsanvisninger

Om brugen af denne værktøjsmaskine:

•Kontroller, at der under den overflade, der skal

bores, ikke er skjulte elektriske ledninger, gas-

rør eller andre forhindringer (for eksempel med

en metaldetektor).

• Kontroller følgende:

•Svarer maskinens spænding til spændingen

på elnettet?

•Er netledninger, isolering og stik i god stand:

funktionsdygtige, ikke løse eller beskadigede?

• Er der en god, fast forbindelse i stikkontak-

ten?

• Viser boret tegn på unormal funktion, overop-

hedning eller for megen gnistdannelse?

Vægt 5.4 kg

Lpa 88.0 dB (A)

Lwa 101.0 dB (A)

Vibration 9.0 m/s2

Netspænding 230 V

Frekvens 50 Hz

Nominel effekt 850 W

Rotationshastighed,

uden belastning 750/min

Slaghastighed 2920/min

Maks. bordiameter

Beton Ø 28 mm

Stål Ø 13/16 mm

Træ Ø 40 mm

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Economy by Ferm HDM1012 - FEBH-620KS in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Economy by Ferm HDM1012 - FEBH-620KS Manual

Product: