654239

Ecm Mechanika Profi Due Manual

25
Zoom out
Zoom in
Previous page
1/62
Next page
ENGLISH
Instruction manual MECHANIKA & TECHNIKA PROFI DUE
24
1 Water tank machines: Fill water into the water tank.
2 Turn the machine on (power switch in position “1”).
3 Wait until the pressure gauge indicates approx. 1.0-1.25 bar.
4 Depending on the ambient temperature, the heat-up phase is approx. 25 minutes.
5 The machine is now ready for use.
6 Insert the filter holder and move the brew group lever into the upper position and release some hot water. This
way the filter holder will be completely heated.
It is recommended to leave the filter holder in the brew group, keeping it warm for an optimal coffee
dispension temperature.
6.2 Preparing coffee
Use the filter holder with 1 spout and the correspondent filter (1 cup) for the preparation
of 1 cup. Use the filter holder with 2 spouts and the big filter (2 cups) for the
preparation of 2 cups. Make sure that the filter is firmly locked into the filter holder.
Fill the finely ground coffee into the filter.
Use 1 level measuring-spoon of coffee for each cup (approx. 7 g).
Do not overfill the measuring-spoon, as shown in the figure on the right!
Compress the ground coffee with the tamper. Clamp the filter holder firmly
into the brew group.
Place the cup under the spout of the filter holder (for the preparation of 2 cups, put 1 cup under each spout).
Move the group lever into the upper position. During coffee preparation, the overpressure is channeled back over the
water tank adapter. When the cup is filled, move the group lever into the lower position.
The remaining pressure/water will be discharged into the drip tray by the lower part of the infusion cylinder.
The pump pressure can be read on the pump pressure gauge. If the coffee powder is too coarse, a brewing pressure
over 9 bars is not possible.
Advice: After the brewing process, the gauge still indicates a certain pressure. Only when preparing another cup of
coffee the buildup of pressure is visible again.
If the group lever is not moved into the lower position properly, hot water and grounds will squirt out of the brew group
while taking out the filter holder. This may cause injuries.
• Only freshly ground coffee allows for an optimal coffee result. Therefore, use a professional coffee
grinder. In our assortment you will find several professional and compact coffee grinders.
• We recommend to use a stainless steel tamper with a diameter of 58 mm for optimum tamping.
6.3 Dispensing of hot water
1 Place an adequate water container (with a heat-insulated handle) under the hot water dispenser. After having
moved the power switch into the lower position, you can dispense water (e. g. for tea) by opening the hot water
lever.
2 After dispensing water, switch the machine on again. The boiler will be filled with fresh water automatically.
When the machine is switched off, more hot water can be dispensed.
However, one does not necessarily have to switch off the machine for dispensing hot water.
Caution!
Place the nozzle of the dispenser into the water container in order to avoid injuries due to hot water
sprayings.
6.4 Dispensing of steam
The MECHANIKA & TECHNIKA PROFI DUE make it possible to generate large amounts of steam in order to heat or
froth beverages, e. g. milk or punch. It is a professional and compact espresso coffee machine with an enormous
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ecm Mechanika Profi Due at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ecm Mechanika Profi Due in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 4,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info