782668
14
Zoom out
Zoom in
Previous page
1/20
Next page
Phone: 866-356-1992 | Email: Support@eccotemp.com | Address: 315 - A Industrial RD Summerville, SC 29483
10 Product Support: Eccotemp.com/help-desk Shop Online: Eccotemp.com/products Store Locater: Eccotemp.com/locater
PLEASE NOTE: THIS MANUAL IS SUBJECT TO CHANGE AT ANY TIME, TO ENSURE THIS MANUAL IS UP TO DATE PLEASE VISIT OUR HELP DESK
AT WWW.ECCOTEMP.COM FOR ALL OF OUR PRODUCT MANUALS.
INSTALLATION LOCATION & METHOD CONTINUED...
7) Connect the valve cover.
Water connections
1. All water pipe must comply with national and applicable state and local water pipe codes.
2. The unit should be connected directly to the main water supply. Flush pipe with water to remove any debris or
loose particles
3. It is required that 3/4” NPT water connections be used with the following models, iE11, iE18, iE24, iE27.
4. Please remember to install rubber seal rings at the connections. When all water connections are completed,
check for leaks and take corrective action before proceeding.
5. Connect the cold water supply to the threaded pope labeled “Inlet” and the hot water to the threaded pipe
labeled “o\Outlet”. IMPORTANT: RUBBER WASHER MUST BE USED FOR PROPER SEAL.
Electrical connection
1. All electrical work must comply with national and applicable state and local electrical codes
2. All units must be connected to a properly grounded dedicated branch circuit of proper voltage rating.
3. Before beginning any work on the electric installation, be sure that main breaker panel switch is OFF to avoid
any danger of electric shock, all mounting and plumbing must be completed before proceeding with electrical
hook-up.
4. iE11 can be connected to a single circuit, use a supply cable protected by a double pole breaker. Connect the
cold water supply to the threaded pope labeled :inlet” and the hot water to the threaded pipe labeled “outlet”.
IMPORTANT: RUBBER WASHER MUST BE USED FOR PROPER SEAL.
5. iiE18 require two independent circuits. Use two supply cables protected by two separate double pole breakers.
6. iE24, iE27 require three independent circuits. Use three supply cables protected by three separate double pole
breakers.
7. While feeding the cable to terminal blocks, please make sure the metal wire ends and the terminal blocks touch
completely. Then tighten the screws to make sure there is full contact and the current can go through.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eccotemp iE series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eccotemp iE series in the language / languages: English as an attachment in your email.

The manual is 3.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info