611763
10
Zoom out
Zoom in
Previous page
1/44
Next page
7-4-2011 Rev2 10 IR Link Pro Flush
1. Bringen Sie die 3IREDB Emitter an den IR-Sensorfenstern der zu steuernden Komponenten in
Ihrem System an. Siehe Abb. 2.
2a. Schließen Sie die gelben Ministecker des 3IREDB an einer der gelben
Buchsen „EMITTERS“ des IRHUB4 Anschlussblocks an.
2b. Schließen Sie das IRQC-Kabel an einer der gelben Buchsen „EMITTERS
des IRHUB4 an und die andere Seite am 3,5 mm Mono IR-Eingang Ihres
AVR. IRED Mono TS 3,5 mm Pin-Konfiguration: Spitze ist IR Data, Manschette
ist Masse (BITTE VERGEWISSERN SIE SICH IN DER BEDIENUNGSANLEITUNG DES
GERÄTS ZUR ENTSPRECHENDEN PIN-KONFIGURATION).
3. Bohren Sie ein 12 mm breites Loch an der Stelle, an der Sie den IR-Empfänger anbringen
möchten. Entfernen Sie die Schraubenmutter, stecken Sie das Empfänger-Kabel und -gewinde
durch das Loch, so dass die Linse in den Raum weist (und eine freie Sichtverbindung zur Hand-
Fernbedienung hat). Schrauben Sie die Mutter wieder so fest auf, dass sie den Receiver in seiner
Position halten kann
4. Schließen Sie den roten Ministecker des IRLPRO Flush IR-Receivers an der roten Buchse „IR
RCVR“ des IRHUB4 Anschlussblocks an.
5. Schließen Sie das 12 V DC Netzteil an einer nicht geschalteten 230 V~ 50 Hz Steckdose an.
BITTE BEACHTEN: Es ist wichtig, dass Sie eine nicht geschaltete Steckdose benutzen, so dass das IR-
System ständig für System-Einschaltbefehle aktiv ist.
6. Schließen Sie den 2,1 mm „C“ Stecker der Spannungsversorgung an der Buchse „+12VDC“ des
IRHUB4 Anschlussblocks an.
STATUS
Sie können ein Spannungsstatussignal an den IRLPRO Flush IR-Receiver durch Anschluss einer
Spannungsversorgung (nicht mitgeliefert; 5 – 24VDC & 5- 12 VAC) übertragen, die beispielsweise
durch das zu steuernde Gerät geschaltet wird. Wird das A/V-Gerät oder der Kontakt
eingeschaltet, so leuchtet die bernsteinfarbene Status-LED im IRLPRO Flush IR-Receiver auf und
zeigt Ihnen damit an, dass das A/V-Gerät eingeschaltet ist (siehe Abbildung 3). Der
Eingangsspannungsbereich ist 5 – 24VDC & 5- 12 VAC. Buchse 2,1 mm Pin-Konfiguration: Mitte/rot
ist +V DC, Manschette/schwarz ist Masse.
Oben auf dem Schrank befindet sich ein Ausschnitt für die Platzierung einer Steckbrücke. Die
Standardposition der Steckbrücke ist die Parkposition JP1. Es gibt Anzeigen für drei verschiedene
Abb 2
Abb 3
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ebode IR Link Pro Flush at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ebode IR Link Pro Flush in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info