515345
16
Zoom out
Zoom in
Previous page
1/32
Next page
16
7. OPERATION
7.1 Self check at power on
After power on the alarm unit checks battery, mains power and telephone-line conditions. If one of these tests fails an
appropriate message will be announced (battery error/power failure/line-check error).
Three beep: Mains power loss AND battery low at the same time!
Quickly handle the announce problem, otherwise the alarm functions are not guarantied.
7.1.1 Detection of wired sensor
EasyAlarm
®
detects the connected motion sensor automatically during the switching on procedure (factory setting). This
sensor is activated for presence verification
Important notes:
By disconnecting the motion detector during the operation mode, an alarm is triggered followed by the
announcement: ”alarm due to sensor 1, sensor failure!”
By connecting the motion detector after the start up procedure of the alarm unit, an alarm is triggered followed by
the announcement: “alarm due to sensor 1, sensor 1 activated!”
7.2 Arm / Disarm system
After power on EasyAlarm
®
automatically arms the system. During operation EasyAlarm
®
can be armed/disarmed
using the remote control or during any telephone connection using DTMF 7 and 9 .
Announce “supervision activated “ or “supervision deactivated”
7.3 Inactive waiting period
7.3.1 After power on or changing position of selection switch (exit delay)
EasyAlarm
®
remains inactive for 20 seconds (LED is on continuously), to leave time to quit your room/house without
triggering an alarm. An emergency call by pressing the emergency button is still possible.
Note:
The entry/exit period can be adjusted according to section 10.3.
If there are unacknowledged alarms, their quantity and the reason of the last alarm will be announced.
If presence verification is activated, following announcement is made: "Presence verification activated".
Key Action
5 Announcement of the monitored functions (inactive waiting period will be restarted)
7
Bypass waiting period and change to inactive supervision mode
Attention: by switching from activated to inactivated supervision mode, an announcement of the
supervision modes is made and the waiting period starts again.
9
Bypass waiting period and change to active supervision mode
Attention: by switching from inactivated to activated supervision mode, an announcement of the
supervision mode is made and the waiting period starts again.
others Test-call will be made to the first calling number
7.3.1.1 Announcement of the supervision functions
The supervision functions can be activated or deactivated individually on each position of the selection switch
EasyAlarm
®
deactivated announcement: "Supervision I/II/III deactivated"
EasyAlarm
®
activated announcement: "Supervision I/II/III
followed by the supervision mode of the activated type of monitoring:
acoustical monitoring announcement: "due to noise"
sensor-1 monitoring announcement: "due to sensor 1”
sensor-2 monitoring announcement: "due to sensor 2”
sensor-3 monitoring announcement: "due to sensor 3” .. “activated”
7.3.2 ..after an successful alarm
EasyAlarm
®
remains inactive for two minutes (LED is on continuously) to avoid too many alarms due to sensor contacts.
An emergency call is still possible during this period. Any key-press results in a test call to the first calling number.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EasyAlarm CONTROL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EasyAlarm CONTROL in the language / languages: English as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of EasyAlarm CONTROL

EasyAlarm CONTROL User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info