515345
13
Zoom out
Zoom in
Previous page
1/32
Next page
13
6. PROGRAMMING
Important note:
All the programmed parameters remain stored even without battery.
You can prevent your system from unintended re-programming according to section 6.4.1. If you use this
protection feature message „programming deactivated, PIN“ will be announced when the function switch is
on position PROG.
Three beep: Mains power loss AND battery low at the same time!
6.1 How to program new calling numbers
EasyAlarm
®
supports nine calling numbers that can be programmed as follows:
1. Slide function switch to PROG
2. Enter * * <n> (selected calling number: Standard n = 1..9)
Select number will be announced followed by “to modify press star“
3. If you like to change this calling number, press * , otherwise proceed with step 5
4. Enter new calling number. To delete an existing number enter * and proceed with step 5
5. Slide function switch to OFF
Notes:
Every keystroke will be acknowledged by a beep
Key #. programmes a dialling delay of 5 seconds, provided it is entered between two digits, e.g. a delay is essential in
a private exchange (first digit + #. + calling number).
If your private exchange needs a flash pulse to start an internal call, following programming is possible:
2. #. followed by the extension number.
Key *. is used as separator for Point-ID protocol section 6.1.1.
If a programming error occurs, put function switch to OFF and repeat point 1 to 5.
Important notes:
Calling number 1 cannot be deleted due to safety reasons.
6.1.1 Point-ID (Contact-ID) alarm protocol
If the alarm should be transferred to a alarm organisation using the Point-ID (Contact-ID) protocol, the alarm number has
to be followed by key * and the customer-ID. EasyAlarm forwards the protocol to this alarm number and connects
hereafter to the following calling number in standard hands-free connection mode
Alarm number Customer-ID
074567890 3456
Example for programming the calling number: 0 7 4 5 6 7 8 9 0 * 3 4 5 6 .
Note:
The first character * , that follows the alarm number will not be transmitted (=> separator). The customer ID is a four
digit code. In case of an alarm the following codes are transmitted according to the <Alarm reason> and the <Zone>.
Code
<Alarm reason> <Zone>
602 Alarm due to cyclic test 900
602 Alarm due to remote programming "**#" 900
301 Alarm due to power failure 900
601 Alarm due to key-press (test-call) 900
132 Alarm due to noise monitoring 900
140 Alarm due to hardware sensor 1 901
140 Alarm due to hardware sensor 2 902
140 Alarm due to hardware sensor 3 903
120 Alarm due to emergency button 902
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for EasyAlarm CONTROL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of EasyAlarm CONTROL in the language / languages: English as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of EasyAlarm CONTROL

EasyAlarm CONTROL User Manual - German - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info