772472

Easy Threed Nano Manual

5
Zoom out
Zoom in
Previous page
1/11
Next page
(A) If the light flash at fast rate, means the extruder is heating, it needs to wait about 1 minute,
once extruder complete heating, the light will flash at steady rate. Then wait another 10 seconds,
Motor begins to pull the material into extruder gear. If the filament comes out from the nozzle,
means filament installed successfully. Then slide the switch back to the middle gear, the indicator
light become normal light without flashing.
(B) If the light become flash at steady rate, it needs to wait about 10 seconds, Motor begins to pull
the material into extruder gear, filament comes out from the nozzle, means filament installed
successfully. Then slide the switch back to the middle gear, the indicator light become normal light
without flashing.
Precaution: After the first filament installation, there is no need to repeat the work of feeding
filament every time, when print different models. Only need to feed when the filament runs out.
Retract:
If want to replace another roll of filament or the machine does not print for long time. Then needs
to retract the filament. First slide switch to “RETRACT” gear, the print button in front will flash green
light at fast rate or at steady rate.
(A) If light flash at fast rate, means the extruder is heating, it needs to wait about 1 minute, once
extruder complete heating, the light will flash at steady rate. Then wait another 10 seconds, Motor
begins to work, use hand to pull the material until it completely retract from the tube, then slide
the switch back to middle gear. The indicator light become normal light without flashing.
(B) If light flash at steady rate, it needs to wait about 10 seconds, Motor begins to work, use hand
to pull the material until it completely retract from the tube, then slide the switch back to middle
gear, the indicator light become normal light without flashing.
Precaution: After feeding and retracting, both needs to slide the switch back to the middle gear (at
the back of printer), then the indicator light become normal light without flashing.
4.2 Slicing model
Download models from easythreed model library in SD card or to download from internet, then
slicing in E3D Nano software and copy to SD card, please refer to the instruction of 3D NANO slicing
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Easy Threed Nano at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Easy Threed Nano in the language / languages: English as an attachment in your email.

The manual is 0.44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info