702341

Dyson V10 Manual

37
Zoom out
Zoom in
Previous page
1/80
Next page
37
EN
USING YOUR DYSON APPLIANCE
PLEASE READ THE ‘IMPORTANT SAFETY INSTRUCTIONS’ IN THIS DYSON
OPERATING MANUAL BEFORE PROCEEDING.
DOCKING STATION INSTALLATION
• Unpack the docking station, plug and installation leaflet.
• Select the location for the docking station and ensure that there is no pipework
(gas, water or air), electrical cables, wires or ductwork directly behind the
mounting location.
• Follow the instructions on the installation leaflet.
• Click the attachments into place.
• Place the appliance in the docking station.
• Plug in the docking station and turn on to charge.
• Your appliance will need to be fully charged before first use.
The docking station must be mounted in accordance with regulations and
applicable codes/standards (state and local laws may apply).
Dyson recommends the use of protective clothing, eyewear and materials when
installing the docking station.
VACUUMING
• Remove the appliance from the docking station.
• Check that the underside of the cleaner head or tool is clean and free from foreign
objects that may cause damage.
Before vacuuming your flooring, rugs and carpets, check the manufacturer’s
recommended cleaning instructions.
The brush bar on the appliance can damage certain carpet types and floors. Some
carpets will fuzz if a rotating brush bar is used when vacuuming. If this happens, we
recommend vacuuming without the motorised floor tool and consulting with your
flooring manufacturer.
LIGHTS DURING CHARGING
LIGHTS DURING USE
LIGHTS DIAGNOSTICS
FILTER AND BLOCKAGE INDICATOR LEDS
EMPTYING THE CLEAR BIN
• Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
• Ensure that the appliance is disconnected from the charger before emptying the
clear bin. Be careful not to pull the 'ON' trigger.
• Avoid pulling the 'ON' trigger when emptying.
• Remove the wand by pressing the red wand release button and pulling away from
the bin.
• To release the dirt:
– Hold the appliance with the bin in a downwards position.
– Firmly push the red bin release button.
– The bin will slide down, cleaning the shroud as it goes.
– The bin base will then open.
– The bin base will not open if the red button is not pushed down fully.
To minimise dust/allergen contact when emptying, encase the clear bin tightly in a
plastic bag and empty. Remove the clear bin carefully from the bag. Seal the bag
tightly, dispose as normal.
CLEANING THE CLEAR BIN (OPTIONAL)
If it is necessary to clean the clear bin:
• Follow the instructions in the 'Emptying the clear bin' section.
• Press the red button located on the bin runner to release the bin and slide the bin
off the runner.
• Clean the clear bin with a damp cloth only.
• Ensure that the clear bin and seals are completely dry before replacing.
• To refit the clear bin:
– Insert the spine on to the bin runner.
Close the clear bin by pushing the bin base upwards until the clear bin and bin base
click into place.
The clear bin is not dishwasher safe and the use of detergents, polishes or air
fresheners to clean the clear bin is not recommended as this may damage
your appliance.
FILTER AND BLOCKAGE INDICATOR LEDS
Your appliance has two indicator lights that will help alert you that simple
maintenance steps are needed.
• The filter indicator will flash intermittently when the filter unit is not fitted correctly.
Follow the instructions on how to refit the filter unit in the 'Washing the filter unit'
section.
• The filter indicator will light continuously when the filter unit needs washing. Follow
the instructions on how to wash the filter unit in the 'Washing the filter unit' section.
• The blockage Indicator LED will light if there is a blockage. Follow the instructions
on how to clear blockages in the 'Looking for blockages' section.
WASHABLE PARTS
Your appliance has washable parts, which require regular cleaning. Follow the
instructions below.
WASHING THE BRUSH BARS
Your appliance has two washable brush bars, check and wash these regularly
according to the following instructions to maintain performance.
• Ensure the appliance is disconnected from the charger before removing the brush
bar. Be careful not to pull the ‘ON’ trigger.
To remove, wash and replace brush bars:
• Please refer to the ‘Washing the brush bars’ illustrations alongside the
instructions below.
• Turn the cleaner head upside down so the underside of the cleaner head is facing
you. Use a coin to turn the fastener one quarter anti-clockwise until it clicks into the
unlocked position.
• Rotate the end cap to the open position. Gently slide the large brush bar away from
the cleaner head.
• Remove the end cap from the large brush bar. Do not wash the end cap.
• Lift out the small brush bar from the octagonal end and pull away from the
cleaner head.
• Hold the brush bars under running water and gently rub to remove any lint or dirt.
• Stand both brush bars upright. Ensure the large brush bar is stood upright as
shown. Leave to dry completely for a minimum of 24 hours.
• Before replacing, check that the brush bars are completely dry. Refit the small brush
bar before the large one. Insert the round end of the small brush bar into place.
Push down the octagonal end until it clicks into place.
• Reattach the end cap to the brush bar.
• Slide the large brush bar back onto the cleaner head, around the motor. The end
cap should be in the open position as shown. Once in place, rotate the end cap
back into the closed position.
Charging, low charge
Charging, medium charge
Charging, nearly full
Fully charged
High level of charge
Medium level of charge
Low level of charge
Empty, needs charging
Battery fault-call Dyson Helpline
Main body fault-call Dyson Helpline
Charger fault-call Dyson Helpline
Blockage indicator
Filter unit not fitted correctly
See battery section
Filter unit requires washing
… 37 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dyson V10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dyson V10 in the language / languages: All languages as an attachment in your email.

The manual is 8,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dyson V10

Dyson V10 User Manual - English - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info