761230
14
Zoom out
Zoom in
Previous page
1/64
Next page
14
Use caution when removing the casing.
The casing may have sharp edges/
corners which may cut or cause harm.
1. Place the main body on a cloth to
avoid marking its surface.
2. Remove the (2) security screws from
the main body, using the service tool
provided. Store safely.
3. Lift the backplate out of the main
body.
4. If cable entry is to be from the rear,
remove the rubber cable grommet
from the rear cable entry hole. Store
safely.
2
1
3.2
Positioning.Unpacking.Contents.
EN
Side cable entry.
IMPORTANT
Cable entry can be either from the
left or the right. Decide which before
you start.
The unit is designed to have only one
side cable entry point.
NOTE: If the side entry option is
chosen, a fifth hole will need to be
drilled in the wall.
Make sure you work on the correct
side for the installation. The break-
out on the main body must match up
with the bracket on the backplate.
Once the break-out panel on the
main body has been removed there
is no option to swap sides.
CAUTION
Before installation decide if the cable
entry is to be from (3.1) the rear or
(3.2) the side. Follow the relevant
instructions.
NOTE
This product is not recommended for
mounting onto porous wall surfaces
(e.g. plaster) without a back panel,
to avoid discolouring or damage to
unprotected walls. (A back panel for this
product is available from Dyson.)
Recommended height measurements are
from the floor.
1300mm adult male.
1265mm adult female.
928mm children 58 years old.
1028mm children 8–11 years old.
1108mm children 11–14 years old.
1050mm wheelchair user.
211m m
Side cable
entry
Backplate
Main body
Side cable
entry
Rear cable
entry
CAUTION: Do not use the backplate
as a guide when drilling. Ensure no
pipe work (gas, water, air) or electrical
cables, wires or ductwork are located
directly behind the drilling/mounting
area.
NOTE: If the side entry option is chosen,
a fifth hole will need to be drilled in the
wall. See step 3.2.
1. Select the appropriate height.
Recommended heights are shown,
but may need to be adjusted for
each individual installation.
2. Minimum clearances are: above,
30mm; sides, 220mm. There should
be no obstruction between the unit
and the floor.
3. Measure the location on the wall. If
cable entry is to be from the rear, the
1. Ensure you work only on the side of
the fascia that you have chosen for
the cable entry point.
2. Use pliers to carefully nip out only
one pre-marked break-out panel in
the correct side of the main body.
Align to one of the edges and break
off an initial part of the panel.
3. Align to the other edge and break
off an initial part of the panel.
4. Break off the whole part from the
centre.
5. Clean up any excess plastic.
6. Drill holes.
CAUTION: Do not use the backplate
as a guide when drilling. Ensure no
pipe work (gas, water, air) or electrical
cables, wires or ductwork are located
directly behind the drilling/mounting
area.
7. Pull the electricity supply cable
through the side bracket and side
bracket seal as shown. Ensure
that cable is long enough to route
correctly through the backplate to
the terminal block. (Note: cable
length will be different for left and
right side entries.)
NOTE: Ensure suitable cable gland/
conduit connector is used (not
provided) for the installation.
Fixing the backplate to the wall.
Fit the main unit securely to the wall
using the appropriate fixings for
the wall type and weight of the unit.
Slide the side bracket into the recess
between the wall and the backplate.
Screw to the wall and secure with the
appropriate fitting.
Do not use counter-sunk screws.
Main unit x 1
Side bracket and
seal assembly
Service tool x 1
RightLeft ● Primary fixing locations (x4).
Do not use countersunk screws.
5th hole for side entry
6mm
REAR VIEW REAR VIEW
24mm
to top of
fascia
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dyson AB12 - Airblade V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dyson AB12 - Airblade V in the language / languages: All languages as an attachment in your email.

The manual is 19,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dyson AB12 - Airblade V

Dyson AB12 - Airblade V Additional guide - English - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info