650110
5
Zoom out
Zoom in
Previous page
1/28
Next page
8 9
- Check that voltage indicated on the rating label corresponds to the mains
voltage in your home.
- Wash all parts (except body) with warm soapy water.
Assembling
- While holding the head, inset it into the inlet
(g.1). Rotate the head in the same direction as
g.2 until a click can be heard. Move the head
slightly to ensure it is placed in securely.
- Place the feed screw into the head (long end
rst) by turning the feed screw until it is set into
the motor housing (g.3).
- Place the cutting blade onto the feed screw
shaft with the blade facing the front as
illustrated (g.4). If it is not tted properly, meat
will not be ground.
- Place the desired cutting plate next to the
cutting blade, tting protrusions in the slots
(g.5).
- Support or press the centre of the cutting plate with one nger then screw
the xing ring until tight with the other hand (g.6). Do not over tighten.
- Place the hopper plate on the head and x into position.
- Place the unit on a at, non slip surface.
- The air passage at the bottom and the side of the motor housing should be
kept free and not blocked.
First Time Use
Instructions for Use
Cleaning and Maintenance
Mincing Meat
- Cut all food into pieces (boneless and fatless meat is recommended, approx
20mm x 20mm x 60mm) so that they fit easily into the hopper opening.
- Plug in and press the ON/OFF button to turn on the machine.
- Feed food into the hopper plate. Only use the food pusher (fig.7)
- After use, switch the unit off and unplug it from the power supply.
Reverse Function
- In case of jamming, switch the appliance off by pressing the ‘ON/OFF
button and press the "REV" button.
- Feed screw will rotate in the opposite direction and the head will become
empty.
- If it doesn’t work, switch the unit off and clean it.
Disassembling
- Make sure that the motor has stopped completely.
- Disconnect the plug from the power outlet.
- Disassemble by reversing the steps from images 6-1.
- If the xing ring is not easily removed by hand, please use tools in g 12.
- To remove the cutting plate easily, place a screwdriver between the cutting
plate and the head as illustrated and lift it up (g.13).
- Press the unlock button before removing the head. Holding the head, rotate
it in the same direction as g. 14. The head can then be removed easily.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Duronic MG1600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Duronic MG1600 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info