613283

Durkopp Adler 527 Manual

8
Zoom out
Zoom in
Previous page
1/34
Next page
4
6.4 Adjustment of the upper thread tension
(Fig. 1, 2, 5)
The tension of the upper and that of the bottom thread must be
mutually adjusted in such a way, so that the stitch locking is being
done in the middle of the sewn material (Fig. 5). The tension of the
upper thread is to be adjusted by turning a bit the nut of the tensioner
(M, Fig. 2). In turning the nut to the right (in the clockwise direction),
we increase the tension of the upper thread, in turning it in the
opposite direction, we reduce the tension of the thread.
When the machine is provided with a thread cutter of thread (version
-105), its correct function is to be given major attention in adjusting
correctly the thread tension. It is necessary to set correctly the
auxiliary tensioner (L, Fig. 1) the function of which influences the
length of the upper thread end which is projecting from the needle
eye after having cut the thread. When correctly setting of the tensio-
ner, the quality of the initial stitches is good and no unthreading of
the thread out from the needle occurs. When increasing the adjusted
tension of the auxiliary tensioner this end is shorter (the seam
starts are of better quality), but there is an increased danger that this length will not be sufficient for starting further stitching,
when the thread would leave the needle eye. In the opposite case, namely with a too small tension, the given ends are uselessly
too long which worsens the quality of the stitch start on the rear side of the sewn material.
6.5 Change of the hook bobbin, threading and setting of the bottom thread tension (Fig. 6, 7)
Caution!
Do not start the machine before placing the hook covers in their working (protective) position.
Before changing the bobbin in the hook, switch off the main switch and put your feet off the pedals on the stand to
avoid the machine start by treading the pedal.
Using the flap (F), remove the bobbin case from the hook.
Put the full bobbin (A) into the bobbin case (B) and guide the thread through the groove (C) under the braking spring (D) and then
into the hole (E).
Let free about 5 – 6 cm of the thread end. It is recommended to turn the bobbin in the arrow direction when pulling the thread.
After having inserted the bobbin case into the hook be sure in assuring this by the flap (F). As usual, by means of the the upper
thread, we thread the bottom thread above the throat plate.
The tension of the bootom thread is regulated by a screw (G). In turning it in the (+) direction, the pulling power increases, in the
(-) direction it is reduced. When the tension of the bottom thread is correctly adjusted, then a good stitch laying is generally being
ensured by the respective adjustment of the upper thread tension by means of the tensioner nut.
Fig. 6
Fig. 5
D
C
+
-
B
A
E
D
C
Fig. 7
F
F
G
Correct adjustment
of the tension of both
threads
Incorrect adjustment
Incorrect adjustment
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 527 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 527 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Durkopp Adler 527

Durkopp Adler 527 User Manual - German - 34 pages

Durkopp Adler 527 User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info