613305
4
Zoom out
Zoom in
Previous page
1/17
Next page
Pneumatic Clamp Opening
The stroke of the holder clamp is a maximum 20 mm. This stroke allows
the working of almost all sewable materials and leather thicknesses.
Electric Thread Burning Device
The thread separator device separates the needle and underthread by
burning immediately at the top edge of the material. The synthetic
threads are melted together at the ends. The thus created hardening
hinders a loosening of the seam and a unthreading of the needle thread.
MICROCONTROL Controls
The complete control of the sewing unit occurs via a microcomputer. It
assumes the control tasks, monitors the sewing process and indicates
operator errors and malfunctions.
1.3 Technical Data
Sewing area: maximum 60 x 100 mm
Needle system: 428; 428 Serv Nm 250;
794 (for thick sewing material only)
Needle thickness: Nm 120 - Nm 280
depending on the type of sewing thread
and the sewing material.
Yarns: Synthetic yarns
Nm 30/3 - 8/3
Bobbin capacity: 23 m with 18/3 yarn
Stitch type: Double saddle stitch type 301
Number of stitches: 1100 / min
Number of stitches per 42, 58, 72 (without gear reducer)
guide curve revolution: 84, 116, 144 (with gear reducer)
Seam formation 72 stitches in 3.5 sec. or
144 stitches in 7 sec.
Looping stroke: 5 mm
Clamp stroke: max. 20 mm
Sewing material thickness: max. 16 mm (sewing material pressed
together by the clamp)
Power: 0.55 kW
Motor rpm: max. 2800 rpm
Operating pressure: 6 bar
Air consumption: approx. 1,2 NL per work cycle
Nominal voltage: 9880 506001 3~380-415 V + N, 50 Hz
9880 506002 3~220-240 V, 50 Hz
9880 506003 3~220-240 V, 60 Hz
The unit is supplied with one of the
listed voltage kits appropriate to the
nominal voltage.
Dimensions: (H x W x D) 1720 x 1100 x 736 mm
The listed height dimension applies to
the work height of the frame set at the
factory.
Put-through area: 210 x 140 mm
Work height: 760...1060 mm (upper edge of the table
top)
Weight: 160 kg
Noise level Lc: 83 dB (A)
Workstation related emission according to DIN 45635-48-B-1
Number of stitches: 1.000 min-1
Commanding cam: (Stitches) 116
Sewing cycles: 9,7 s on / 2,0 s off
Sewing material: 2x girdle tape 1,5 mm 1.260 g/m
2
Measuring point to DIN 4895 Part 1
X = 0 mm Y = -400 m Z = 300 mm
6
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 506 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 506 in the language / languages: English as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Durkopp Adler 506

Durkopp Adler 506 User Manual - German - 22 pages

Durkopp Adler 506 User Manual - French - 17 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info