613310
10
Zoom out
Zoom in
Previous page
1/35
Next page
6
6.3 Regulating the thread tension
The thread tension must conform to the thickness of the sewn
threads, thickness and hardness of sewn material (thin and
soft material will fold with high tension) and the kind of seam.
An ordinary fitting seam should be formed with stitches knit-
ted in the middle of the sewn material.
A decorative seam is mostly used with rough threads (10, 20)
on thin material and it has tied up threads on the reverse side
of the material for achieving a decorative appearance.
Thread tension adjustment is by standard sewing (table 3)
conditions in accordance with table No. 4.
If achieving of a decorative seam with stitch knitting on the
underside is wished, it is necessary to decrease the upper
thread tension, it is carried out by turning of nuts (1), in the
counter-clockwise sense.
Thread tension
Table 4
Sewing Kind of seam Identified Maximum
category value upper tension of
thread tension lower thread
NN
1- 31
2 - 4.5 1.5
3
Fitting 8
2
Decorative 5
4
Fitting 12 2
Decorative 10 2.5
If the maximum lower thread tension exceeds the
values given in table No. 4, it may cause problems
in the beginning of sewing after the previous
thread trim.
Measurement of tension is done by dynamometer.
Warning:
The upper thread tensioner has been loosened automatically
after every trimming and top roller lifting. In these cases the
thread tension cannot be measured.
Regulating the thread tension
Caution! Risk of injury!
Before regulating the lower thread tension, turn
the main switch off and wait until the motor stops.
The upper thread tension is adjusted with nuts (1). Its clock-
wise turning increases the tension.
The tension of the auxiliary tensioner (3) should beas low as
possible but it should be on a level so that the upper thread
would not pull out of the tensioner when the work is being
removed.
The lower thread tension is adjusted with a screw (2). Its clock-
wise turning increases the tension.
Tension correlation rate defines the depth of the seam tied
through. The result of raising the upper tension will be the
decreasing depth of tie through. The opposite will apply with
the lower thread.
Fitting seam
Decorative seam
Stitch knitting
Stitch knitting
2
3 3
1
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 4280i - 6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 4280i - 6 in the language / languages: English as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Durkopp Adler 4280i - 6

Durkopp Adler 4280i - 6 User Manual - German - 35 pages

Durkopp Adler 4280i - 6 User Manual - French - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info