613310
34
Zoom out
Zoom in
Previous page
1/35
Next page
12
5.2.2 Changes of setting parameters of stopmotor setting considering original producer setting
Parameter Parameter
No value
111 - Max. revolutions (according to a type of machine)
116 180 Trimming revolutions
170 - Reference position
171 30 First position of needle
192 340 Delay angle of tensioner switch on
202 120 Delay of start run after switch off the signal foot
225 3 Type of the machine
5.3 Setting stopmotor S359 600052 XX-EFKA VD 552/6F82FA and S359 600056 XX-EFKA VD 554/6F82FA
5.3.1 Setting position reader
Positions are set by means of discs with cut outs directly in position reader.
Setting bottom position:
- Disassemble the cover of position reader
- Disconnect head power supply cable from drive
- Switch on the power supply switch
- Step treadle shortly down forwards (machine stops in first position of needle)
- Switch off the power supply switch
- Turn the beginning of cut out 1 of coinciding discs so that machine would stop at the value 135° of the hand wheel
- Carry out check by repeating procedure
Setting upper position of thread lever:
- Step treadle down backwards (machine stops in upper position of needle)
- Switch off the power supply switch
- Turn the beginning of cut out 2 of separate disc so that machine would stop at the value 65° of the hand wheel
- Carry out check by repeating procedure
5.3.2 Changes in parameters of stopmotor setting considering original producer setting
Parameter Parameter
No value
111 Max. revolutions (according to a type of machine)
116 180 Trimming revolutions
136 ON Stitch by thread trimmer (back)
192 86 Delay angle of tensioner switch on
202 120 Delay of start run after switch off the signal foot
6. Examination of sewing
Caution! Risk of injury!
Before threading a thread switch the main switch off and wait until the motor stops.
- Check the sense of turning the hand wheel – according to the arrow situated on it.
- Thread a thread.
- Choose sewing material.
- Switch the desirable function on the control panel of stopmotor. Examination should be carried out with selection of fancy bar.
- First sew slowly then speed up the sewing.
- If the stitch does not meet requirements, follow the first part of instructions manual or service book.
2 A
1 A
1
2
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Durkopp Adler 4280i - 6 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Durkopp Adler 4280i - 6 in the language / languages: English as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Durkopp Adler 4280i - 6

Durkopp Adler 4280i - 6 User Manual - German - 35 pages

Durkopp Adler 4280i - 6 User Manual - French - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info