678582

Dual CS 503-1 Manual

7
Zoom out
Zoom in
Previous page
1/14
Next page
4.
Set the required tracking force
for
the cartridge used
by
turning
the
dial 4. The tracking force for series cartridges DMS 249
E
= 15 mN
=
dial position
1.5.
Note:
If a
different cartridge
is
used, refer
to
the separate cartridge
data sheet
for the
necessary setting values.
Set
the
appropriate value
of
the antiskating device
10 on the
basis
of
the follow/ing table:
O Setting
for
spherical
styli.
O Setting
for
biradial (elliptical) styli (DMS
249 E).
Tracking force
Antiskating setting
10
Tracking force scale
4
"Dry" playing "Wet" playing
1
=10 mN
1 0.7
DMS
1.25 =
12.5
mN
1.25 0.8
249
1.5 =15 mN 1.5 1.0
2
= 20 mN
2
1.3
2.5
=25 mN
2.5
1.8
3
= 30 mN
3 2.1
Start,
cue control
- Select
the
required platter speed
of 33 or 45
rpm,
by
means
of the
switch
6,
swivel
the
stylus protection
cap
upwards.
- Now position the tone arm over the lead-in groove of the record.
The
tone
arm is now
lowered slowly onto
the
record using
the
cueing
lever
5. The
tone
arm is
lowered slowly,
tus
preventing damage
to
your records.
- The tone
arm can be
raised
at any
position, also
for
brief interrup-
tions when playing,
by
means of the cue control lever (cueing lever
in
position
The
platter continues
to
rotate
in
this case.
Stop
- At the end of the record, the tone arm is
raised,
and the unit switches
off automatically.
- You can also switch
off
the turntable
by
setting the cueing lever
5 to
position
• and
repositioning
the
tone
arm to the
tone arm post.
Changing
and fitting the cartridge
A
Vi
inch cartridge with
a
net weight
of
3
...
10
g
can be fitted
in
place
of the cartridge already fitted
or
on units without
a
cartridge.
The Dual range
of
accessories offers appropriate cartridges.
- Loosen screw
8 and
remove
the
head shell
by
pulling
it
forward.
Remove
the
cartridge
by
loosening the
two
securing screws
9.
Pull
off the connection wire on the cartridge. Attach the new cartridge,
at
first loosely, on
the
head shell. Secure the connection wires with
the
connection
pin on the
cartridge.
Red
R
right channel blue GL left channel ground
Green
RG
right channel ground white
L
left channel
- Replace
the
head shell
on the
tone
arm and
secure screw
8.
- Attach
the
cartridge with
the aid of
the system installation gauge.
- This has been correctly installed
if
the
tip of
the stylus
-
viewed from
above
- is in
the V-shaped recess
of
the system installation gauge.
Viewed from the side, the stylus must be in the aera
of
the rectangu-
lar recess (Fig.
6).
Stylus
The stylus
is
subject
to
natural wear
and
tear during playing.
We
therefore recommend regular checks, which should
be
carried
out
after
at
least
300
playing hours
in the
case
of
diamond-tipped
styli.
Your dealer will
be
happy
to do
this
for you
cost-free. Worn
out or
damaged (chipped) styli damage records. Therefore, only
use as
replacements
the
stylus types recommended
in the
technical data
of
the cartridge. Other styli often cause audible reductions
in
quality
and
increased wear
to
records. Remove
the
stylus
by
pulling
it
diagonally
downwards.
To
fit a
stylus in, follow
the
procedure
in
reverse order (fig.
4).
Electrical
safety
The unit conforms
to
the international safety specifications lEC 65 (VDE
0860) and
to
the guidelines
of
the European Community, 82/499/EWG
(VDE 0875).
FRANQAIS
1 Gapot
2 Charnière
3 Contrepoids
du
bras
de
lecture
4 Réglage
de la
force d'appui
du
bras
de
lecture
5 Levier lève-bras
6 Réglage
de la
vitesse
7 Support
et
verrouillage
du
bras
de
lecture
8 Ecrou
de
fixation
de la
tête
de
pick-up
9
Vis de
fixation
du
phonocapteur
10 Réglage antiskating
11 Blocage
du
plateau (en dessous
du
revêtement)
12 Fiche
du
cordon secteur
13 Fiches Cinch pour
le
raccordement
14 Cosse
de
masse
Préparatifs
Retirez l'appareil
et
tous
les
accessoires
de
l'emballage. Conservez
tous
les
éléments
de
l'emballage pour
un
éventuel transport ultérieur.
- Poser le plateau
et
presser
sur
l'arrêt
pour qu'il s'enclenche dans
la
rainure
de l'axe du
plateau (fig.
1).
Mettre le tapis
sur le
plateau.
- EmboTtez
les
charnières
2
dans
les
évidements prévus
a eet
effet
(fig.
2).
7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dual CS 503-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dual CS 503-1 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 5,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info