678582

Dual CS 503-1 Manual

6
Zoom out
Zoom in
Previous page
1/14
Next page
Austausch bzw. Einbau des Tonabnehmers
Anstelle
des
eingebauten Tonabnehmers
bzw. bei
Geraten ohne
Tonabnehmer kann ein
y2-Zoll-Tonabnehmer
mit
einem Eigengewicht
von
3 ... 10 g
eingebaut werden.
Das Dual-Zubehörprogramm bietet entsprechende Tonabnehmer an.
- Mutter
8
lösen,
und
Tonkopf nach vorne abziehen (Fig.
4).
Tonab-
nehmer durch Lösen
der
zwei Befestigungsschrauben
9 ab-
nehmen.
- AnschluBleitungen
am
Tonabnehmer abziehen. Neuen Tonabneh-
mer zuerst lose am Tonkopf befestigen. AnschluBleitungen
mit den
AnschluBstiften
des
Tonabnehmers befestigen.
Rot
R
rechter Kanal blau GL linker Kanal Masse
Grün
RG
rechter Kanal Masse weiB
L
linker Kanal
- Tonkopf wieder
auf
Tonarmrohr aufstecken
und
Mutter
8
fest-
schrauben.
- Befestigen
Sie den
Tonabnehmer
mit
Hilfe
der
mitgelieferten
Ein-
baulehre
am
Tonkopf.
- Die Montage
ist
korrekt, wenn die Abtastnadel
-
von oben betrach-
tet
- in der
V-förmigen Aussparung
der
Systemeinbaulehre steht.
Von
der
Seite betrachtet, muB
die
Nadel
im
Bereich
der
rechtecki-
gen Aussparung stehen (Fig.
6).
Abtastnadel
Die Abtastnadel
ist
durch den Abspielvorgang natürlichem VerschleiB
ausgesetzt.
Wir
empfehlen daher eine regelmaBige Uberprüfung,
die
bei Diamant-Abtastnadein nach mindestens
300
Spielstunden erfol-
gen sollte.
Ihr
Fachhandler wird dies gern kostenlos
für Sie tun.
Abgenutzte oder beschadigte (abgesplitterte) Abtastnadein zerstoren
die Schallplatten. Venwenden
Sie bei
Ersatzbedarf
nur die in den
Technischen Daten des Tonabnehmers empfohlene Nadeltype. Nach-
geahmte Abtastnadein verursachen oftmals hörbare Qualitatsverluste
und erhöhte Schalipiatten-Abnutzung. Ziehen
Sie die
Abtastnadel
schrag nach vorne
ab.
Das Einsetzen
der
Abtastnadel erfolgt
in
umgekehrter Weise (Fig.
4).
Elektrische
Sicherheit
Das Gerat entspricht
den
internationalen Sicherheitsbestimmungen
lEG
65
(VDE 0860)) und den EG-Richtlinien 82/499/EWG (VDE 0875).
ENGLISH
1 Dust cover
2 Hinge
3 Tone arm counterbalance
4 Tracking force adjustment
for
tone
arm
5 Cueing lift lever
6 Speed selector
7 Tone arm support with tone arm lock
8 Head-shell locking
nut
9 Screws
for
mounting cartridge
10 Antiskating adjustment
11 Platter locking (beneath
the
platter
mat)
12 Mains lead plug
13 Audio Cinch plugs
14 Earth wire
Preliminary operations
Unpack
the
unit
and all
accessories. Please keep
the
packaging
for
future use when transporting
the
device.
- Fit the platter and depress the locking mechanism
in
lts centre until
it
engages in the groove
of
the platter spindle
(fig.
1). Place the platter
mat
in
position.
- Insert
the
hinges
2 in the
appropriate recesses
(fig. 2).
Slide
the
cover
1
parallel
to the
position
of the
hinges
2
(opening angle
approximately 60°) until
it
locks in position. In this position, the cover
can
be
removed
at
any time.
Connection
to the AC
mains
-
The
turntable must
be
connected
to a
mains voltage
of 230 V/
50-60
Hz or to 115 V/60 Hz in
accordance with
the
voltage
Information
on the
rating plate.
- The unit can also
be
connected
to
the socket
of
appropriately fitted
amplifiers.
- The set carries voltage even when stopped.
It is
necessary to unplug
it from
the
mains outlet
to cut
power
off.
Connection
to amplifier or receiver
- Gonnect
the
audio cables
to the
phono-magnetic inputs
of the
amplifier
or
receiver (red RCA-type plug
=
right channel, white RCA-
type plug
=
left channel).
- Connect earth wire
14 to the
earth connector
of
your amplifier.
Balancing the tone arm and setting the tracking
and antiskating force
1.
Switch
off the
antiskating device
10.
2.
Turn the tone arm counterbalance
3
on the tone arm (fig. 3). Uniock
the tone
arm and
move
it
over
the
tone
arm
rest. Place
the cue-
control lever
5 in X
position. Hold
the
tonearm whilst doing
so.
3. Balancethetonearm precisely by turning the counter-balance. The
tonearme
is
balances precisely when
it
pivots freely.
6
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dual CS 503-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dual CS 503-1 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish as an attachment in your email.

The manual is 5,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info