801302
16
Zoom out
Zoom in
Previous page
1/48
Next page
16
Instructions for use ROTEC
Drive Medical GmbH & Co. KG | As per: 28.04.2021 | Errors and alterations excepted
EN
456
Never swivel the footrests inwards!
Length and angle adjustment
of the footrest
Length adjustment
(photo 7)
Use the enclosed Allen
wrench to loosen the
screw on the footrest and
adjust the length as desi-
red by shifting up or down.
Retighten the screw!
Angle adjustment
(photo 8)
Use the enclosed Allen
wrench to release the
screw on the footrest until
it can be pulled out of the
toothed wheel inwards.
Now rotate the footrest
into the desired position
and press it back into the
toothed wheel.
Retighten the screw!
Adjusting seat height (rear wheel mount)
The height of the seat at
the rear can be adjusted
in increments. To adjust
it, remove both hand rim
wheels by pressing the re-
lease button (see section
Attach wheels”). Unscrew
the nut of the wheel mount
and move it into the desi-
red hole.
Replace the nut with the
locking washer and tigh-
ten it (photo 9).
Ensure that the wheel axle is properly tightened!
Adjusting seat height (front wheel mount)
The height of the seat can be adjusted in increments and
is correspondingly adjusted in the desired inclination
of the seat surface. To adjust, unscrew the wheel axle
screw and pull it out.
The plugs of the corres-
ponding holes can be ea-
sily exchanged. Now move
the wheel in the desired
position and reinsert the
wheel axle screw and tigh-
ten it (photo 10).
Ensure that the wheel
axle is properly tightened!
Adjusting the height of the backrest
The height of the backrest
can be adjusted in incre-
ments.
Note: When the backrest
is adjusted, the height of
the push handles is also
automatically adjusted.
To adjust the backrest,
remove the left and right
nuts under the guide tube
of the backrest (photo 11).
Pull the screws out. Now adjust the desired height by
pulling or pushing on the respective push handle.
Reinsert the screws, put on the knurled nuts and tighten
them.
Always ensure that both sides are adjusted identically.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Drive Rotec at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Drive Rotec in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 8.52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info