488598
13
Zoom out
Zoom in
Previous page
1/88
Next page
13
SAFETY WARNINGS SPECIFIC FOR
WIRE BRUSHING OPERATIONS
a. Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress the
wires by applying excessive load to the brush. The wire
bristles can easily penetrate light clothing and/or skin.
b. If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or
brush with the guard. Wire wheel or brush may expand in
diameter due to work load and centrifugal forces.
c. Do not exceed 15000 min
-1
when using wire brushes.
!
WARNING
Do not work with materials containing
asbestos (asbestos is considered
carcinogenic).
!
WARNING
Take protective measures during work
when dust can develop that is harmful
to one's health, combustible or explosive (some dusts are
considered carcinogenic); wear a dust mask and work with
dust/ chip extraction when connectable.
ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
ONLY FOR EUROPEAN COUNTRIES
Do not dispose of power tools into household waste!
According the European Guideline 2002/96/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that
are no longer usable must be collected separately and
disposed of in an environmentally correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Voltage Rating . . . . . . . . . . . . . . . 7,2V
Amperage Rating
. . . . . . . . . . . . 0,7Ah
No Load Speed
. . . . . . . . . . . . . . . n
o
10000/20000 min
-1
Collet Capacity . . . . . . . . . . . . . . . 0,8mm, 1,6mm, 2,4mm, 3,2mm
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
ASSEMBLY
ALWAYS TURN OFF THE TOOL BEFORE CHANGING ACCESSORIES,
CHANGING COLLETS, OR SERVICING THE TOOL.
GENERAL
The Dremel multitool is a high quality precision tool that can be
used to perform detailed and intricate tasks. The wide range of
Dremel accessories and attachments allow you to perform a large
variety of tasks. These include tasks such as sanding, carving and
engraving, cutting, cleaning and polishing.
PICTURE 1
PICTURE 2
A. Collet Nut
B. Collet
C. Housing Cap
D. Shaft Lock Button
E. Grip
F. Ventilation Openings
G. On/Off Switch and Speed Dial
H. Release Tab
I. Battery
J. Charger
CHARGING THE TOOL
The Cordless Rotary Tool is not fully charged. The tool is equipped
with a removable battery pack. Be sure to charge pack prior to
initial use.
To charge the tool:
1. Put the switch in the “OFF” position. PICTURE 2
2. Squeeze the release tabs on both sides of the battery pack
and remove pack from back of tool. PICTURE 2
3. Align exterior shape of battery pack with exterior shape of
charger (arrows on battery will point to the arrows located
on charger), squeeze release tabs, insert battery pack into
charger and release pressure on tabs so it locks in place.
4. Plug charger into the power source. The green LED light
indicates connection has been made and the battery pack is
charging. Under normal use the tool requires 3 hours charging
time to reach full capacity.
5. When charging is completed, squeeze release tabs and
remove battery pack from charger.
6. Align exterior shape of battery pack with exterior shape of the
housing of tool. Squeeze release tabs, insert battery pack into
back of tool and release so it locks in place.”
IMPORTANT CHARGING NOTES
1. The battery pack accepts only about 80% of its maximum
capacity with its first few charge cycles. However, after the
first few charge cycles, the battery will charge to full capacity.
2. The charger was designed to fast charge the battery only
when the battery temperature is between 4 ºC and 41 ºC.
3. A substantial drop in operating time per charge may mean
that the battery pack is nearing the end of its life and should
be replaced.
NOTE: Use of chargers or battery packs not sold by Dremel will void
the warranty.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dremel 7700 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dremel 7700 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 4,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info