488597
24
Zoom out
Zoom in
Previous page
1/100
Next page
24
2. Remove the brushes from the tool by pulling on the spring that
is attached to the carbon brush. If the brush is less than 3mm
long and the surface of the brush that touches the commutator
is rough or pitted, the carbon brushes should be replaced. Be
sure to check both brushes. PICTURE 10
3. If one brush is worn, you should replace both brushes for
better performance of your multitool. Remove the spring
from the brush, throw away the old brush and place the
spring on a new brush.
4. Place the carbon brush and spring back into the tool, there
is only one way the brush will fi t back into the tool.
5. Replace the brush caps onto the tool by turning the cap in
a clockwise direction. To tighten, use the wrench, but DO
NOT OVER TIGHTEN! After replacing the brushes the tool
should be run at no load; place it on a clean surface and
run it freely at full speed for 5 minutes before loading (or
using) the tool. This will allow the brushes to "seat" properly
and will give you more hours of life from each set of
brushes. This will also extend the life of your tool since the
commutator surface will also wear better and longer.
CLEANING
!
WARNING
TO AVOID ACCIDENTS, ALWAYS
DISCONNECT THE TOOL AND/OR CHARGER
FROM THE POWER SUPPLY BEFORE CLEANING. The tool can be
cleaned most effectively with compressed dry air. Always wear
safety goggles when cleaning tools with compressed air.
Ventilation openings and switch levers must be kept clean
and free of foreign matter. Do not attempt to clean the tool by
inserting pointed objects through an opening.
!
WARNING
CERTAIN CLEANING AGENTS AND
SOLVENTS DAMAGE PLASTIC PARTS.
Some of these are: gasoline, carbon tetrachloride, chlorinated
cleaning solvents, ammonia and household detergents that
contain ammonia.
SERVICE AND WARRANTY
!
WARNING
NO USER SERVICEABLE PARTS INSIDE.
Preventive maintenance performed by
unauthorized personnel may result in incorrect connection of
internal wiring and components which could cause serious
hazard. We recommend that all tool service be performed by a
Dremel Service Centre. SERVICEMEN: Disconnect the tool and/or
charger from the power source before servicing.
This DREMEL product is guaranteed in accordance with
statutory/country-specifi c regulations; damage due to normal
wear and tear, overload or improper handling are excluded from
the warranty.
In case of a complaint, send the undismantled tool or charger
and proof of purchase to your dealer.
CONTACT DREMEL
For more information on the Dremel product range, support and
hotline, go to www.dremel.com.
Dremel Europe, P.O. Box 3267, 4800 DG Breda, The Netherlands
ÜBERSETZUNG DER ORIGINAL-
BEDIENUNGSANLEITUNG
VERWENDETE SYMBOLE
LESEN SIE DIESE HINWEISE
TRAGEN SIE GEHÖRSCHUTZ
TRAGEN SIE AUGENSCHUTZ
TRAGEN SIE EINE STAUBMASKE
ALLGEMEINE SICHERHEITSHINWEISE FÜR
ELEKTROWERKZEUGE
!
WARNUNG
LESEN SIE SÄMTLICHE
SICHERHEITSHINWEISE UND
ANWEISUNGEN
Die Nichtbeachtung der folgenden Sicherheitshinweise und
Anweisungen kann zu elektrischem Schlag, Feuer und/oder
schweren Verletzungen führen.
Bewahren Sie alle Sicherheitshinweise und Anweisungen
zum künftigen Nachschlagen auf.
Der in den Sicherheitshinweisen verwendete Begriff „Elektro-
werkzeug“ bezieht sich auf netzbetriebene Elektrowerkzeuge
(kabelgebunden) und auf akkubetriebene Elektrowerkzeuge
(kabellos).
SICHERHEIT AM ARBEITSPLATZ
a. Halten Sie Ihren Arbeitsbereich sauber und aufgeräumt.
Unordnung und unbeleuchtete Arbeitsbereiche können zu
Unfällen führen.
b. Arbeiten Sie mit dem Gerät nicht in explosions-
gefährdeter Umgebung, in der sich brennbare
Flüssigkeiten, Gase oder Stäube befi nden.
Elektrowerkzeuge erzeugen Funken, die den Staub oder die
Dämpfe entzünden können.
c. Halten Sie Kinder und andere Personen während der
Benutzung des Elektrowerkzeugs fern. Bei Ablenkung
können Sie die Kontrolle über das Gerät verlieren.
DE
2610Z02333-CN-200S-0211.indb 24 21-2-2011 13:49:06
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dremel 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dremel 200 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info