488597

Dremel 200 Manual

22
Zoom out
Zoom in
Previous page
1/100
Next page
22
A
Y
Y
ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
ONLY FOR EUROPEAN COUNTRIES
Do not dispose of power tools into household waste!
According the European Guideline 2002/96/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that
are no longer usable must be collected separately and
disposed of in an environmentally correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Rated power . . . . . . . . . . . . 125 W
Voltage Rating
. . . . . . . . . . . . . . . 230-240 V, 50-60 Hz
Collet Capacity
. . . . . . . . . . . . . . . 0,8mm, 1,6mm, 2,4mm, 3,2mm
Rated speed (n) . . . . . . . . . . 35000 min
-1
Class II construction . . . . . . . Double insulated construction tools
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
ASSEMBLY
ALWAYS TURN OFF THE TOOL BEFORE CHANGING ACCESSORIES,
CHANGING COLLETS, OR SERVICING THE TOOL.
GENERAL
The Dremel multitool is a high quality precision tool that can be
used to perform detailed and intricate tasks. The wide range of
Dremel accessories and attachments allow you to perform a large
variety of tasks. These include tasks such as sanding, carving and
engraving, cutting, cleaning and polishing.
PICTURE 1
PICTURE 2
A. Collet Nut
B. Collet
C. Housing Cap
D. Attachment interface
E. Shaft Lock Button
F. Ventilation openings
G. Hanger
H. Power cord
I. On/Off Switch and Speed Dial
J. Brush cover (one each side)
COLLETS
The Dremel accessories available for the multitool come
with various shank sizes. Four size collets are available to
accommodate the different shank sizes. Collet sizes are
identifi ed by the rings on the back of the collet.
PICTURE 3
K. 3,2 mm Collet without ring
L. 2,4 mm Collet with three rings
M. 1,6 mm Collet with two rings
N. 0,8 mm Collet with one ring
Always use the collet that matches the shank size of the accessory
you plan to use. Do not force a larger diameter shank into a smaller
collet.
CHANGING COLLETS
PICTURE 4
O. Shaft Lock Button
P. Collet Wrench
Q. To tighten
R. To loosen
S. Collet Nut
1. Press the shaft lock button, hold down and rotate the shaft
by hand until it engages the shaft. Do not engage the shaft
lock button while multitool is running.
2. With the shaft lock button engaged, loosen and remove the
collet nut. Use the collet wrench if necessary.
3. Remove the collet by pulling it free from the shaft.
4. Install the appropriate size collet fully into the shaft and
reinstall the collet nut fi nger tight. Do not fully tighten the
nut when there is no bit or accessory installed.
CHANGING ACCESSORIES
PICTURE 5/6
T. Shaft Lock Button
1. Press the shaft lock button and rotate the shaft by hand
until it engages the shaft lock. Do not engage the shaft lock
button while multitool is running.
2. With the shaft lock button engaged, loosen (do not remove)
the collet nut. Use the collet wrench if necessary.
3. Insert the bit or accessory shank fully into the collet.
4. With the shaft lock button engaged, fi nger tighten the collet
nut until the bit or accessory shank is gripped by the collet.
NOTE: Be sure to read the instructions supplied with your Dremel
accessory for further information on its use.
Use only Dremel tested, high performance accessories.
2610Z02333-CN-200S-0211.indb 22 21-2-2011 13:49:05
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dremel 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dremel 200 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 2,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info