745854

Dovre VIRTUS 50 GA Manual

55
Zoom out
Zoom in
Previous page
1/215
Next page
DOVRE
Subject to change because of technical improvements
13
Roof sleeve through a pitched roof
of flammable material
Read the "Installation Conditions" chapter care-
fully and follow the installation instructions
below.
1. Start at the stove and add the concentric pipes
one at a time, including the changes in direction
you want, along the route you decided on in
advance, up to just under the roof.
2. Decide on the location for the roof sleeve.
3. Make an elliptical hole so that a fire separation of
at least 50 mm remains round the pipe.
4. Extend the concentric pipe (1) until it extends at
least 250 mm above the roof surface (more is per-
mitted up to a maximum of 1000 mm stand-alone);
see next figure.
5. Center the pipe using the centering plates (2) and
attach it with the installation bracket (3).
6. Slide a roofing sheet for pitched roof (tar roof) or a
lead slab (4) (tile roof) over the pipe and seal or
cover it watertight.
7. Finish the seam between the pipe and the cone of
the roof sheet or lead slab watertight with silicon
sealant and if necessary a storm collar (5).
8. Install the roof sleeve (6) and secure it with the
clamping strap included in the delivery.
Establishing a gas connection
The connection to the gas pipe is on the back of the
gas regulator block, which is at the bottom right of the
stove.
The connection must meet the following conditions :
A coloured gas valve must be inserted in the gas
supply pipe, as close to the stove as possible and
always accessible.
The connection must be voltage-free.
Have a certified installer make the connection.
Follow the instructions below:
1. Check whether the type of gas and gas pressure
on site correspond with those marked on the type
plate.
The type plate is located on the appliance.
2. Assemble the gas supply pipe. 3/8” G pipe or cop-
per pipe with diameter 10/12 mm suffices for pipes
up to +/- 10 m. 1/2” G pipe or copper pipe with dia-
meter 13/15 mm is used for lengths exceeding 10
m.
3. Install the gas valve.
4. Connect the stove to the gas supply pipe. The gas
connection can be made using the opening on the
back. Use a 3/8” coupling to do this.
5. Check if the supply pipe is gastight (using soapy
water, for example).
Installing the remote control
set
The Mertik Maxitrol GV60 remote control set consists
of a handset (transmitter) and a receiver. The system
works on batteries; connecting an AC adaptor is
optional.
The batteries (2 x 1.5 Volt AAA for the handset
(transmitter), 4 x 1.5 Volt AA for the receiver)
are included.
Use only the Mertik Maxitrol AC adaptor or an
adaptor preapproved by Mertik Maxitrol. Other
adapters probably do not suit your system
and/or can damage it.
Batteries – handset (transmitter)
l 2 x 1.5V AAA (LR 03) (recommended quality:
alkaline).
l Handsets with display: Battery indicator on the dis-
play.
… 55 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dovre VIRTUS 50 GA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dovre VIRTUS 50 GA in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 5,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info