745854

Dovre VIRTUS 50 GA Manual

54
Zoom out
Zoom in
Previous page
1/215
Next page
DOVRE
12
Subject to change because of technical improvements
Follow the instructions below for assembly and see
the figure above.
1. Lead the flexible hose (6) through the existing pipe
(8).
2. Attach the slide (4) to the lower end of the flexible
hose and secure it with two Parker screws (5).
3. Keep the bottom of the slide even with the bottom
of the pipe or the ceiling. Cut the flexible hose at
approximately 100 mm above the chimney cap.
4. Attach the installation plate-outside (9) to the flex-
ible hose, clamp it with a hose clamp (7) and
secure it all with a Parker screw (5).
5. Attach the installation plate-outside (9) watertight
to the chimney cap with silicon sealant and stain-
less steel screws.
6. Install the roof sleeve (11) and secure it with the
clamping strap included in the delivery (10).
After the roof sleeve is installed, the slide (4)
should extend about 100 mm under the pipe or
ceiling.
7. Attach the installation plate-inside (3) gastight on
the bottom of the flue or on the bottom of the ceil-
ing with silicon sealant and stainless steel
screws.
8. Place the stove (1) as indicated in the chapter
“Installation requirements”.
9. Connect the stove with the lower end of the flue
using concentric components (2). All components
must overlap at least 30 mm and be secured with
clamping straps or stainless steel Parker screws
to prevent them from coming apart. Extend the
concentric pipe at least 100 mm into the existing
flue.
The slide (4) should therefore extend about 200
mm into the inner duct of the top concentric
component. If this is not the case, the flexible
hose (6) will be kinked in the chimney, pre-
venting the system from functioning properly.
11. Finally, install the clamp strap in the installation
plate-inside (3).
Roof sleeve through a flat roof of
flammable material
Read the "Installation Conditions" chapter care-
fully and follow the installation instructions
below.
1. Start at the stove and add the concentric pipes
one at a time, including the changes in direction
you want, along the route you decided on in
advance, up to just under the roof.
2. Decide on the location for the roof sleeve.
3. Make a hole with a 250 mm diameter, so that a fire
separation of 50 mm remains round the pipe.
4. Attach a square installation plate (of at least 300
mm and with a sufficiently large centered round
hole) (1) or 2 centering plates with screws to the
bottom of the roof partition to center the pipe; see
following figure.
5. Insert a clamping strap (2) in the installation plate
by first turning it in and then out.
6. Extend the concentric pipe (3) until it extends at
least 400 mm above the roof surface (more is per-
mitted up to a maximum of 1000 mm stand-alone).
7. Slide the roof sheet (4) over the pipe and tighten it
with screws.
8. Finish the seam between the pipe and the cone of
the roof sheet or lead slab watertight with silicon
sealant and if necessary a storm collar (5).
9. Install the roof sleeve (6) and secure it with the
clamping strap included in the delivery.
10. Make sure the roof sheet is covered watertight.
Use lead, tar and/or silicon sealant for this,
depending on the existing roofing.
… 54 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dovre VIRTUS 50 GA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dovre VIRTUS 50 GA in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 5,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info