571311

Dovre 2400BSA Manual

32
Zoom out
Zoom in
Previous page
1/56
Next page
2300 - 2400 32 03.27865.100
3.2. Preparation
Please inspect the fireplace for damage caused during transport immediately after
delivery and notify your distributor in case there are any defects. Do not put the
appliance into operation in the meantime.
In order to avoid damaging the fireplace during installation and to make its handling
easier, it is recommended to remove previously all loose parts (fire-resistant bricks,
grille, ashtray, ...) from the stove. Note the location of those parts while removing
them, so that you have no difficulties in re-assembling the parts later on.
The stove will be supplied with the following parts:
A set of legs
A smoke dome with fixing material
A flue collar with fixing material
A “cold handle” to open the door
An ashtray (option)
3.2.1. Assembly of the legs
Carefully tilt the appliance onto its backside.
Fix the leg holders on the bottom plate with nut M8
and collar Ø8xØ17.
Adjust the height of the leg on the holder with bolt
M8x50, nut M8 and both collars Ø8xØ25.
Fix the adjustment bolts under the legs. These will
allow to adjust the fireplace level.
3.1.4. Combustible material round the fireplace
Within the radiation area of the fireplace
Assure a distance of at least 80 cm between the opening of the fireplace and com-
bustible material. That distance may be reduced to 40 cm if the combustible materi-
al is sufficiently shielded and well ventilated.
Outside the radiation area of the fireplace
Assure a distance of at least 5 cm between the mantle built
around the fireplace and combustible material. A small
surface contact between combustible material and the man-
tle (e.g. wall cladding) is allowed if the mantle of the fire-
place is sufficiently insulated.
A wooden ornamental rafter must not be installed within
the radiation area of the fire. Outside the radiation area,
there must always be a ventilation gap of 1 cm all around to
prevent heat from building up (see picture).
No combustible material must be present within 50 cm from the convection outlet
areas.
min 1 cm
min 1 cm
… 32 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dovre 2400BSA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dovre 2400BSA in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info