Manual Dometic L-2230D Elite (page 7 of 28) (English)

549152

Zoom out

Zoom in

1/28

English

L-2230 Operation

2.05 Fan Modes

Automatic Fan Speeds

Elite has three automatic fan speeds available: high,

medium and low. Automatic Fan Mode allows the Elite to

determine the required fan speed based on temperature

differential. This permits a balance between the most

efficient temperature control and slower, quieter fan

speeds.

Manual Fan Mode

There are three fan speeds available: low, medium and

high. Manual Fan Mode allows the user to select and

maintain the desired fan speed manually. When a manual

fan speed has been selected, the speed is indicated by

one of the 3 LEDs above the AUTO fan LED. The top

LED represents the fastest speed.

Fan Only Mode

The Fan Only Mode can be operated for air circulation

when no cooling or heating is desired. From the Off

Mode press and release the Fan Button to start fan

speed one. Press and release again to select speed two.

Press and release a third time for speed three. Press

and release a fourth time to turn off the fan. Starting a

cycle will revert the fan to the Automatic Mode or the last

selected manual fan setting.

Cycle Fan With Compressor

Press and hold the Fan Button for five seconds. The

mnemonic “CYC” followed by “con” will appear in the

display. Release the button with “CYC” in the window and

the fan will cycle on and off with the compressor. Re-

lease the button with “con” in the window and the fan will

run whenever the system is on.

2.06 Program Mode

The Program Mode is used to adjust the systems

operating parameters to suit the particular needs of

individual users. The Program Mode is also used to tailor

the air conditioning system for the most efficient opera-

tion within an installation. Installation variables such as,

ducting, sensor location and system layout affect the

perceived operation of the overall system. Elite is

shipped with factory programmable default settings which

are stored in memory and can be recalled. However,

reprogrammed settings can be saved as the new default,

thus overwriting the factory defaults (see programmable

parameter P-15).

Entering Program Mode

The Program Mode can only be entered from the Off

Mode. From the Off Mode and in the following order,

press the Mode, Up, Down and the Mode buttons. These

buttons have to be pressed and released in the order

given. The numerals “85” which represent the high fan

limit, appears in the display. The “85” is followed by the

characters “P 1” followed again by the parameter setting

“85”. “P 1” represents the first programmable parameter.

The Elite control is now in the Program Mode.

Restore Default Settings

IMPORTANT ! The default settings can be restored by

entering the Program Mode and setting P-15 to “rSt”. Exit

the Program Mode and the software version number

appears in the display. The default settings are restored

and the Elite control returns to the Off Mode. The

software version number is always displayed when you

exit the Program Mode.

Using the Program Mode

Increment from one parameter to the next by pressing

and releasing the Mode Button while in the program

mode. Decrement from one program parameter to the

previous one by pressing the Fan Button. Use the Up

and Down Buttons to change the program parameter

values. The programmable parameters range from P-1

through P-19. See the Programmable Parameters Table.

Up and Down Buttons

The Up and Down Buttons are used to select the data or

set the desired limits for the parameter being pro-

grammed. This method is followed throughout the

Program Mode, however, special instructions are in-

cluded for individual functions as required.

Exiting the Program Mode

There are two methods to exit the Program Mode. Press

the Power Button and the Elite control will return to the

Off Mode. Not pressing any buttons or attempting any

program changes for 50 seconds will allow the control to

exit the Program Mode to the Off Mode. Any program-

ming changes that were made while in the Program

Mode will be memorized, set as the new default, and put

into operation when the Program Mode is exited and the

control is returned to the On Mode.

Software Identification

The software version of the control is identified for one

second prior to the exit from Program Mode. The soft-

ware identification number (i.e. “A13”) will appear in the

display for one second, then the control will return to the

Off Mode.

NOTE: Should there be any reason to contact Dometic

about the system or programming the Elite, be sure to

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dometic L-2230D Elite in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dometic L-2230D Elite

Dometic L-2230D Elite User Manual - Dutch - 32 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dometic L-2230D Elite Manual

Product: