614840
61
Zoom out
Zoom in
Previous page
1/188
Next page
MANUTENCIÓN USO
INSTALACIÓN
30 mbar Butano (G30)
30 mbar Propano (G31)
28-30 mbar Butano (G30)
37 mbar Propano (G31)
MODELO
APORTACIÓN DE CALOR
NOMINAL COMPLESIVA
VOLUMEN DE AIRE NECESARIO
PARA LA COMBUSTIÓN
I3B/P(30)
AT BE DE DK FI GB NL NO PT SE SI
I3+ (28-30/37)
BE CH ES FR GB IE IT PT SI
CATEGORÍA Y PAÍSES DE DESTINACIÓN PRESIÓN GAS
kW - gr/h m
3
/h
CU322 - CU322M 4,0 - 291 8,0
CU333 - CU333M 4,4 - 320 8,8
CU403PE - CU404PEMW - CU407PEMW 4,6 - 335 9,2
CU354MK 5,1 - 371 10,2
CU352M 5,3 - 386 10,6
CU325 - CU325M - CU404PE - CU405PEMW 5,8 - 422 11,6
CU335 - CU335M - CU402PE - CU414PE 6,2 - 451 12,4
403 - CU351MK - CU404MW - CU407MW 6,4 - 466 12,8
CU433 - CU433M - CU433ML 6,6 - 480 13,2
CU300 - CU300M 6,8 - 495 13,6
CU311 - CU311M 7,2 - 524 14,4
CU400BPE - CU400PE - CU401PE 7,4 - 539 14,8
404 - CU405MW 7,6 - 553 15,2
402 - 414 8,0 - 582 16,0
400 - 400B - 401 9,2 - 669 18,4
61
ESPAÑOL
La conexión del artefacto a la red de gas se hará con tubería metálicagida y con piezas de empalme estancas.
Puede emplearse también un tubo flexible, si se tienen en cuenta las siguientes indicaciones:
a) Que se pueda inspeccionar siempre;
b) Que no esen contacto con partes calientes ( como las partes que están debajo de los quemadores);
c) Que esprotegido contra cualquier tensión (torsión, racción,aplastamiento,...);
d) Que esprotegido contra daños de las partesviles empotradas (por ej. un cajón);
e) Que tenga una longitudxima de 1,5m;
f) Que sea sustituido antes de la fecha de vencimiento;
Una vez efectuada la conexión verificar la estanqueidad del circuito vertendo sobre las uniones una solución
jabonosa la cual evidenciará la eventual salida de gas formando burbujas, NO UTILIZAR LLAMAS LIBRES.
Este artefacto puede funcionar con los siguientes gases y las relativas presiones de alimentación. La categoría (o las
categorías) según las cuales ha sido regulado el artefacto está indicada claramente en la etiqueta de identificación que
está pegada en el artefacto.
CONEXIÓN DEL GAS
CONTROLAR ESTOS DATOS ANTES DE CONECTAR EL ARTEFACTO AL BOMBONA.
LOS REDUCTORES DE PRESIÓN QUE SE DEBEN UTILIZAR ENTRE EL BOMBONA
Y EL ARTEFACTO DEBEN ESTAR CONFORMES CON LAS CATEGORÍAS INDICADAS
EN LA TABLA SUBYACENTE.
DURANTE LAS OPERACIONES DE INSTALACIÓN Y CONEXIÓN, EL TUBO
CONDUCTOR DE GAS DEL ARTEFACTO NO DEBE SUFRIR TORSIONES,
TRACCIONES U OTROS ESFUERZOS.
61


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dometic CU402PE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dometic CU402PE in the language / languages: All languages as an attachment in your email.

The manual is 15,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info