Manual Dolmar ES-42A (page 27 of 189) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

507645

Zoom out

Zoom in

1/189

complies with the safety regulations. Check in par-

ticular that:

• The chain brake is working properly;

• The run-down brake is working properly;

• The bar and the sprocket cover are fitted correctly;

• The chain has been sharpened and tensioned in

accordance with the regulations;

• The mains cable and mains plug are undamaged;

Refer to the “CHECKS “section.

2. Always ensure in particular that the extension cable

used is of adequate cross-section (see “SPECIFICA-

TIONS”). When using a cable reel, wind the cable

completely off the reel. When using the saw in the

open air, ensure that the cable employed is intended

for open-air use and is rated accordingly.

3. Do not operate the chain saw in the vicinity of flamma-

ble dust or gases, as the motor generates sparks and

presents a risk of explosion.

4. Work only on firm ground and with a good footing. Pay

particular attention to obstacles (e.g. the cable) in the

working area. Take particular care where moisture,

ice, snow, freshly cut wood or bark may make sur-

faces slippery. Do not stand on ladders or trees when

using the saw.

5. Take particular care when working on sloping ground;

rolling trunks and branches pose a potential hazard.

6. Never cut above shoulder height. (Fig. 1)

7. Hold the chain saw with both hands when switching it

on and using it. Hold the rear handle with your right

hand and the front handle with your left. Hold the han-

dles firmly with your thumbs. The bar and the chain

must not be in contact with any objects when the saw

is switched on.

8. Clean the area to be cut of foreign objects such as

sand, stones, nails, wire, etc. Foreign objects damage

the bar and chain, and can lead to dangerous kick-

back.

9. Take particular care when cutting in the vicinity of wire

fences. Do nut cut into the fence, as the saw may kick

back.

10. Do not cut into the ground.

11. Cut pieces of wood singly, not in bunches or stacks.

12. Avoid using the saw to cut thin branches and roots, as

these can become entangled in the chain saw. Loss of

balance presents a hazard.

13. Use a secure support (trestle) when cutting sawn tim-

ber.

14. Do not use the chain saw to prise off or brush away

pieces of wood and other objects.

15. Guide the chain saw such that no part of your body is

within the extended path of the saw chain. (Fig. 2)

16. When moving around between sawing operations,

apply the chain brake in order to prevent the chain

from being operated unintentionally. Hold the chain

saw by the front handle when carrying it, and do not

keep your finger on the switch. Withdraw the mains

plug when taking breaks or leaving the chain saw

unattended. Leave the chain saw where it cannot

present a hazard.

17. Withdraw the mains plug when taking breaks or leav-

ing the chain saw unattended. Leave the chain saw

where it cannot present a hazard.

Kickback

1. Hazardous kickback may arise during work with the

chain saw. Kickback arises when the tip of the bar (in

particular the upper quarter) comes into contact with

wood or another solid object. This causes the chain

saw to be deflected in the direction of the operator.

(Fig. 3)

2. In order to avoid kickback, observe the following:

• Never begin the cut with the tip of the bar.

• Never use the tip of the bar for cutting. Take particu-

lar care when resuming cuts which have already

been started.

• Start the cut with the chain running.

• Always sharpen the chain correctly. In particular, set

the depth gauge to the correct height (refer to

“Sharpening the chain” for details).

• Never saw through several branches at a time.

• When limbing, take care to prevent the bar from

coming into contact with other branches.

• When bucking, keep clear of adjacent trunks.

Always observe the bar tip.

• Use a trestle.

Safety features

1. Always check that the safety features are in working

order before starting work. Do not use the chain saw if

the safety features are not working properly.

- Chain brake:

The chain saw is fitted with a chain brake which brings

the saw chain to a standstill within a fraction of a sec-

ond. It is activated when the hand guard is pushed for-

wards. The saw chain then stops within 0.15 s, and

the power supply to the motor is interrupted.

- Run-down brake: (Fig. 4)

The chain saw is equipped with an run down brake

which brings the saw chain to an immediate stop when

the ON/OFF switch is released. This prevents the saw

chain from running on when switched off, and thus

presenting a hazard.

-The front and rear hand guards protect the user

against in jury from pieces of wood which may be

thrown backwards, or a broken saw chain.

- The trigger lockout prevents the chain saw from

being switched on accidentally.

-The chain catcher protects the user against injury

should the chain jump or break.

Transport and storage

................... When the chain saw is not in use or is

being transported, withdraw the mains

plug and fit the scabbard supplied with

the saw. Never carry or transport the

saw with the saw chain running.

1. Carry the chain saw by the front handle only, with the

bar pointing backwards.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar ES-42A in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Dolmar ES-42A Manual

Product: