507649
20
Zoom out
Zoom in
Previous page
1/28
Next page
20
Electrode gap
The electrode gap must be 0.5 mm.
Checking the ignition spark
- Press the loosened spark plug with the ignition cable Þ rmly
connected against the cylinder using insulated pliers (not
near the spark plug opening).
- ON/OFF switch in the "I" (ON) position.
- Pull the starter cable hard.
If the function is correct, an ignition spark must be visible near
the electrodes.
CAUTION:
Do not touch the spark plug or plug cap if the engine is
running (high voltage).
Switch off the engine before starting any maintenance work.
A hot engine can cause burns. Wear protective gloves!
The spark plug must be replaced in case of damage to the
insulator, electrode erosion (burn) or if the electrodes are very
dirty or oily.
- Remove the Þ lter cover (see "Cleaning the air Þ lter").
- Pull the plug cap (G/1) off the spark plug. Use only the
combination wrench supplied with the saw to remove the
spark plug.
CAUTION: Use only the following spark plugs:
BOSCH WSR 6F or NGK BPMR 7A.
Replacing the spark plug
Cleaning the air Þ lter
F
G
1
- Remove the Þ lter cover (E/1) (2 screws).
- Loosen the screws on the air Þ lter (E/2) and remove from
intake manifold.
- Loosen the screw on the preÞ lter cover (E/3) and remove.
- Remove preÞ lter (E/4).
IMPORTANT:
Cover the intake opening with a clean cloth to prevent dirt
particles from getting into the carburetor.
- Pry apart the top and bottom of the air Þ lter as shown in
Figure F.
CAUTION:
To prevent injury to the eyes, do NOT blow out dirt particles!
Do not use fuel to clean the air Þ lter and preÞ lter.
E
2
4
1
3
- Clean the air Þ lter and preÞ lter with a soft brush.
- If the Þ lter is very dirty, clean it in lukewarm water with dish-
washing detergent.
- Let the air Þ lter dry completely.
- Put the top and bottom sections back together.
- Before reinstalling the air Þ lter, check the intake opening and
remove any dirt particles. If there are any, remove them with
a brush.
Clean frequently (several times a day) when working in very
dusty or dirty conditions. Full engine power is possible only with
a clean air Þ lter and preÞ lter!
Important: For sawing dry wood and working on dusty ground
we recommend using a Robkoß ok air Þ lter (available as an
accessory). The Robkoß ok Þ lter keeps out even the smallest
dust particles.
CAUTION: If the air Þ lter or preÞ lter becomes damaged,
replace immediately!
Pieces of cloth or large dirt particles can destroy the en-
gine!
H
0,5 mm
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dolmar 115 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dolmar 115 in the language / languages: English as an attachment in your email.

The manual is 3,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Dolmar 115

Dolmar 115 User Manual - German - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info