766079

Dogtrace d-control AQUA spray 900 Manual

10
Zoom out
Zoom in
Previous page
1/15
Next page
10
Important: Before pairing the transmitter and receiver, make sure that no one else
in your vicinity is using their own d-control. Your receiver could receive the code
of another transmitter. If this happens, re-pair your receiver with your transmitter.
Switching o:
1. Place the lower part of the transmitter near the red target on the receiver - indicator
light will shine red, then orange.
2. Once the light is orange remove the transmitter from the receiver - the light will
shine red.
Pairing procedure
1. Turn on the transmitter.
2. The receiver must be o.
3. On the transmitter, select the position (button 1 / 2), you want to pair with.
4. Place the lower part of the transmitter to the red target on the receiver and hold for
5 seconds. The LED indicator of the receiver will shine red, then orange.
5. After 5 seconds the orange indicator light will ash 3 times.
6. Remove the transmitter from the receiver - alternating green and red lights will ash.
7. Press the acoustic signal button on the transmitter. Successful pairing is indicated
by a long beep of the receiver.
Re-pairing the receiver
The number of times you may re-pair the receiver is unlimited, either with the same or
a dierent transmitter (see Pairing the receiver with the transmitter).
TIP: An unlimited number of receiver can be paired with one transmitter.
Example: On button 1 we pair 3 receivers, which can be paired one after another or
by putting all receivers in pairing mode and then pressing the acoustic signal button.
All of these receivers will respond the same when you press the command button.
For example, it's possible to use two training collars on one dog. Or alternatively for
training multiple dogs, where the same command is issue to all of them at once.
Important: When turning on, simply put the bottom of the transmitter on the
receiver's target for approx. 1 second. If you hold the transmitter at the receiver
target for more than 5 seconds, the receiver enters pairing mode. This mode is
indicated by alternating ashes of green and red indicator light. If this happens,
follow the chapter below - Pairing the transmitter and receiver.
Pairing the receiver with the transmitter
Each transmitter has its own radio code. For the transmitter to communicate with
the receiver, they must be paired together. If you have purchased a new d-control
transmitter/receiver set, no pairing is necessary – the set is already paired. Pairing is
only done if you want to use another transmitter or receiver.
The transmitter is designed for training two dogs, so you may pair it with two receivers.
Use buttons 1 and 2 to select one dog or the other.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Dogtrace d-control AQUA spray 900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Dogtrace d-control AQUA spray 900 in the language / languages: English as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info