163678
5
Zoom out
Zoom in
Previous page
1/12
Next page
Low level input
Use a pair of shielded stereo audio cables with RCA
type jack. Most trunk-mount amplifiers need a 20
feet RCA cable ( appr 5 – 6 meters). Most under
the seat installations require 12 feet ( 2 – 3 meters)
RCA cables. Avoid placing the RCA cable close to
speaker cables, power
cables and remote control
cable. Connect to RCA input
sockets.
Set the input selector switch
to position ”Low level”.
High Level Input for ch 1 & 2 on RA20 and RA40
Connect left and right speaker wires coming from
the car stereo to the high level input as shown. You
must connect both plus and minus as the inputs
are balanced, connecting plus only gives lower level
and bad sound quality. By changing the polarity of
plus and minus, you can change the phase.
High level input socket for CH 1 & 2
Hi level input
socket on amp.
Automatic turn on when using high level input.
With the ”Input selector switch” set to High level
and the ”High level Auto Start” switch set to IN,
the amplifier turns on automatically on high input.
You don´t need to connect a separate remote wire
from your head unit.
If you want to use high level
input but use a remote start
wire, just set the ”High level
Auto Start” switch to OUT.
Input and controls
Input Wiring
Inputs may be low level from the RCA output of the
car stereo or high level from the car stereo speaker
output. Low level = RCA is to prefer for the best sound
quality.
RA40 high level input for ch 3 & 4.
The RA40 four channel amplifier is connected
likewise, however we have four channels.
You can feed all four channels using high level in-
put, or feed two channels from RCA and two
channels using high level input from rear speaker
cables.
5
RA20 & RA40
CH2 CH1
CH4 CH3
Hi level input plug.
Hi level input
socket on
amp.
Hi level input plug.
Green: Left +
Black: Left -
Black: Right -
Grey: Right +
Green: Left +
Black: Left -
Black: Right -
Grey: Right +
To ensure best possible performance from the
amplifiers a switch is installed to select between
Hi and Low input.
When using High Level input:
Push in the button to position
”High Level”
When using Low level input:
Push out the button to position
”Low Level”
To ensure best possible performance from the
amplifiers when used with high level input a switch
is installed to select between Automatic amplifier
start and remote wire start.
When using High Level input with
automatic start:
Push the button to position IN
When using High level input with
remote wire start:
Push out the button to position OUT
NOTE!
Some head units use BTL output IC:s that have a
constant 12 Volt + on the speaker terminal, also
when shut off (the Power LED indicator lights
constantly even when the head unit is off). In this
case you have to use a separate remote wire
connected to the REMOTE-terminal instead.
High / Low level input switch
Hi level auto start switch
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DLS ra20 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DLS ra20 in the language / languages: English as an attachment in your email.

The manual is 0,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info