67943
6
Zoom out
Zoom in
Previous page
1/12
Next page
Crossovers
Input Level control
The input level control, 7V – 0,2 V,
matches the output of your radio to
the input of the amplifier. After instal-
lation is complete, make sure the in-
put of the amplifier is turned down all
the way ( counter-clockwise at 7V ).
The DLS Reference amplifiers include high pass
filter (HP) and low pass filters (LP). The highpass
filter on RA25 can also be used as a subsonic filter.
The slope of all filters are 12 dB / octave.
The high pass filters can be switched off if you want to
run the amplifier in full range mode.
This is the crossover configuration on RA25 & RA30:
RA25:
HP-filter 20 - 150 Hz
RA30 CH 1 & 2: RA30 CH 3 & 4:
HP-filter 45 -125 Hz LP-filter 40 - 125 Hz
Subsonic filter 25 Hz
The HPF ( high pass filter )
blocks very low frequencies from
reaching the speakers. It is
mostly used at say 60 Hz to
protect small speakers ( like 6
inch and smaller ) from deep
bass. It can also be used as
subsonic filter to take away the
very deepest frequencies from a
bass box. The typical setting is
then around 25 – 40 Hz.
High Pass Filter / Subsonic filter
Low Pass Filter
The LP-filter ( low pass filter) is
mostly used for subwoofers. It will
allow low frequencies only and
blocks higher frequencies.
A typical setting is 50 – 80 Hz.
The filter can be switched IN-OUT
and is available on RA30 sub
channel only.
6
Play a tape or CD, make sure all bass or treble
settings or equalizer are flat, and turn the volume
of the radio up until you just start to hear distortion.
Turn the volume control down just a bit. On the
amplifier increase the input level control ( clockwise
or to the right ) until you just start to hear distortion,
then back the level control just a bit. Now your ra-
dio and amplifier levels are matched.
Grand bass 40 Hz
Grand Bass is used to increase the bass volume
with a center frequency of 40 HZ. You can select
the amplification between 0 dB ( no amplification )
and +18 dB (full amplification).
The phase control on RA30 sub
channel 3&4 can be set
continuously from 0 - 180
degrees. This is very useful when
you want to adjust the bass
sound for best front stage image.
Start on 0 and turn the control
slowly clockwise until you
experience that the bass sound
is coming from the front. If you
dont get the result you want, also
try to phase reverse the
subwoofer connections and
make a new adjustment.
Phase control
RA25 & RA30
This function is used to
compensate for the bass box
function and to adjust for your
own taste of bass. Set level
control at 0 dB if you want it
to be inoperative. This
function is operative only on
RA30, channels 3 & 4.
PHASE
0
180
DEGREE
BASS
0
+18
dB
GAIN
7V
0,2V
HP-filter
FREQUENCY
20
150
Hz
LP-filter
FREQUENCY
40
125
Hz
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DLS RA 30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DLS RA 30 in the language / languages: English as an attachment in your email.

The manual is 0,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info