66428

DLS CAD 11 Manual

6
Zoom out
Zoom in
Previous page
1/12
Next page
Bass boost control is used to set
the bass volume. You can select the
amplification between 0 dB and +18
dB at a 45 Hz center frequency.
This function is used to compensate
for the bass box function and to adjust
for your own taste of bass. Set level
control at 0 dB if you want it to be
inoperative.
Bass boost control
RCA Output
Use RCA Outputs to
connect additional
amplifiers.
Ouput Input
AA
B
B
Single amplifier system
You can fine tune your bass level
from the front of your car. Connect
the external bass level control box to
the remote socket on the rear panel.
Remote Bass level control
Bass Level
Remote
Testing
Before you finish the installation, you should do the
following tests to make sure the wiring is correct
and everything is operating properly.
Test power wiring
1. Turn on the head unit but do not turn up
the volume. The amplifier power light
should come on. If not, check the remote
and +12 volt wires. Also check the ground
connection.
2. Turn up the head units volume slightly. All
speakers should operate. if not, check
wiring connections at amplifier and
speakers.
The Subsonic filter at 25-30 Hz and the LPF filter
setting at 60-80 Hz.
Filter settings
From low level
output of head unit
To input of
additional amps.
Reconnect Battery
When wiring is complete,
reconnect the battery
negative terminal.
NOTE!
Minimum speaker load is one (1) ohm. You can
connect four 4 ohm subwoofers or two 2 ohm
subwoofers to the amplifier. Loads or speaker
impedances less than 1 ohm could result in poor
sound quality and/or damage to amplifier.
6
Master / Slave switch
must be set to Master
Connection of DC-input and Remote level control,
see page 7 & 8.
Bass
Boost
0 dB 18 dB
Subsonic
15Hz 50Hz
LPF
15Hz 150Hz
CAD 15
CAD11, CAD15
Bridged
mode
Master
Slave
… 6 …


Need help? Post your question in this forum.

Forumrules
1

Forum

dls-cad-11

Reset search

  • Could someone please tell me what output MOSFET's are used in a DLS CAD11. I have one in for repair but someone removed all of the output MOSFET's. I have tried 31N20 but the amp is getting too hot & going into protection. Submitted on 4-3-2019 at 13:10

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DLS CAD 11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DLS CAD 11 in the language / languages: English as an attachment in your email.

The manual is 0,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info