66428
11
Zoom out
Zoom in
Previous page
1/12
Next page
DLS PERFORMANCE CAD11 CAD15
Number of channels 1 1
Power output in 4 ohm (0,4% THD) 1 x 400 W 1 x 550 W
Max output in 2 ohm (0,7% THD) 1 x 750 W 1 x 900 W
Max output in 1 ohm (1% THD) 1 x 1050 W 1 x 1600 W
All above output power ratings at 13,8 Volt
Signal to noise ratio, A-weighted >100 dB >100 dB
Damping factor >100 >100
Frequency response 15 Hz - 160 Hz 15 Hz - 160 Hz
Input impedance, low level 10 kohm 10 kohm
Input impedance, high level 100 ohm 100 ohm
Input sensitivity 0,15 - 5V 0,15-5 V
Phase control 0-180 degrees variable yes yes
Remote bass level control yes yes
Bass boost adjustable gain @45 Hz 0 - +18 dB 0 - +18 dB
Filter subsonic, 24 dB slope 15 - 50 Hz 15 - 50 Hz
Filter lowpass 24 dB slope 15 - 150 Hz 15 - 150 Hz
Bridge mode (master/slave selector) yes yes
Max size for power cables 21 mm
2
(4AWG) 50 mm
2
(0AWG)
Max size for speaker cables 10 mm
2
(7AWG) 6 mm
2
(10AWG)
Power consumption, idle 1,5 A 2 A
Maximum current draw 120 A 160 A
Built-in fan cooling yes yes
Fuse 4 x 30A 4 x 40A
Dimensions (mm) 70x444x268 70x473x268
Dimensions (inch) 2,92x17,48x10,55 2,92x18,62x10,55
Weight 5,8 kg (12,79 lB) 6,4 kg ( 14,33 lb)
CAD11, CAD15
Specifications
If problems occur during the installation, or later,
this guide might help you to find out whats´s
wrong.
The amplifier is dead:
1. Check power lead, ground and connections at
the amplifier using a multi meter.
2. Check the battery terminal connections.
3. Check the power lead fuse or circuit breaker. If
fuse damage continues, inspect the power lead
for short circuits.
4. Check the amplifier protection fuses. Are these
broken change to new ones with the same
value.
If short circuiting continues, contact your local
DLS dealer. A fault may exist in the amplifier.
5. To start the amplifier requires a remote voltage
of 9-15 volt. Check the voltage with a multi meter.
Amplifier protection fuse blows at low
volume:
One or more speaker cables are shorted. Make an
insulation test with a multi meter. The cables must
not have a connection to earth.
Troubleshooting
The amplifier turns off after 10-30 minu-
tes:
The amplifier is overheating due to inadequate ven-
tilation. Check mounting position is free from
obstruction.
Do this:
1. Move the amplifier to a place with better ventil-
ation.
2. Install one or two fans to cool down the heat-
sink.
3. Overheating can also be caused by an
impedance load below the level permitted.
No output from the speakers:
Check the following:
1. Speaker cable connections to both amplifier and
subwoofers.
2. Signal lead plugs and cables.
11
11


Need help? Post your question in this forum.

Forumrules
1

Forum

dls-cad-11

Reset search

  • Could someone please tell me what output MOSFET's are used in a DLS CAD11. I have one in for repair but someone removed all of the output MOSFET's. I have tried 31N20 but the amp is getting too hot & going into protection. Submitted on 4-3-2019 at 13:10

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for DLS CAD 11 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of DLS CAD 11 in the language / languages: English as an attachment in your email.

The manual is 0,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info